Karcher ICC 2 D ECO 2SB STAGE IIIa - Manual (Page 28)

- 6
 Pull up the handle.
 Press the locking button and release
the handle.
 Pull upwards the lever located under
the seat.
 Slide seat, release lever and lock in
place.
 Check that the seat is properly locked in
position by attempting to move it back-
wards and forwards.
 Turn the hand-wheel at the rear of the
seat.
– In clock-wise direction: Spring harder
– Anti-clockwise direction: Spring softer
 Press the lever (1).
 Slide seat, release lever and lock in
place.
 Check that the seat is properly locked in
position by attempting to move it back-
wards and forwards.
 Tilt the lever (2) until the scales show
your body weight.
– Set the body weight between 50-130
kg.
– If you tilt until the end, the setting is
done for 50 kg.
 Tilt the handle (3).
 Adjust the seat.
 Insert the consumer load at 12V-con-
nection.
(see switch strip)
 Switch on/off the blower.
(see switch strip)
– for heating: level 2
– for air-conditioner: level 3
 Turn on/off the air-conditioner.
(see switch strip)
 Activate the slide.
(see switch strip)
– Slide is pushed in = fresh air
– Slide is pulled out = air circulation
 Activate the slide.
(see switch strip)
– Slide is pushed in = cold
– Slide is pulled out = warm
Note
The appliance is fitted with tension belts for
safe transport.
To unload the machine, proceed as follows:

Remove tension belts.
 Release parking brake.
 Drive down the appliance from the
transport vehicle.
 Park the sweeper on an even surface.
 Remove ignition key.
 Lock parking brake.
ƽ
Danger
Risk of explosion!
– Only use the fuels specified in the Op-
erations Manual.
– Do not refuel the machine in enclosed
spaces.
– Smoking and naked flames are strictly
prohibited.
– Ensure that no fuel reaches the hot
open surfaces.
 Switch off engine.
 Open fuel filler cap.
 Fill in diesel.
 Fill in the tank up to a level 1 cm below
the lower edge of the filling nozzle be-
cause the fuel expands on heating.
 Wipe off any spilt fuel and close fuel fill-
er cap.
– Estimate the fuel requirement in order
to avoid overflows.
– Insert the fuelling gun as deep as possi-
ble into the fuel nozzle. Do not add any
more fuel once the fuelling gun stops
according to the settings.
 Check engine oil level. *
 Check water cooler and maintain it. *
 Check tyre pressure. *
 Check fill level of fuel tank. *
 Adjust driver's seat.
 Check suction channel. *
 Check setting of suction opening. *
 Check lights and ensure that they are
functioning properly. *
 Check signaling and warning systems
for proper functioning. *
 Fill the water reservoir. *
 Check side brush. *
 Empty waste container.
* For description, see section on Care and
maintenance.
ṇ Warning
Rectify any defect you may find immediate-
ly or bring the vehicle to a halt.
 Sit on the driver's seat.
 Do NOT press the accelerator pedal.
 Lock parking brake.
 Switch off the working hydraulic.
 Set the drive direction indicator to posi-
tion (0) (neutral).
 Turn the ignition key to position "I".
Pre-heat lamp glows.
 When the pre-heating lamp goes off,
turn the ignition key to position "II".
 If the machine starts, release the igni-
tion key.
Note
Never operate the starter motor for longer
than 10 seconds. Wait at least 10 seconds
before operating the starter motor again.
 Press the brake pedal.
 Set the drive direction indicator to posi-
tion (1) (drive forwardl).
 Release parking brake.
 Press accelerator pedal down slowly.
ƽ
Danger
Risk of injury! While reversing, ensure that
there is nobody in the way, ask them to
move if somebody is around.

Press the brake pedal.
Parking brake
Lock parking brake
Release parking brake
Adjusting driver's seat
Adjusting the seat position
Adjusting the seat springs
Comfortable seat (accessory)
Adjusting the seat position
Adjusting the seat springs
Adjust seat position
12V connection
Blower
Air-conditioner (accessory)
Fresh air circulation
Heating
Before Startup
Unloading
Start up
General notes
Refuelling
Fuelling using a can
Fuelling using the fuelling gun
Inspection and maintenance work
Operation
Starting the machine
Pre-heat
Start the engine
Drive the machine
Drive forward
Reverse drive
28 EN