Brother HL-2170W - Manual (Page 223)

CHAPTER 5 PJL - 19
Variables Description Sample Value Range
INPUTBUF Sets the receiving buffer size value. 1 to 15 (HL-1650/1670N/2460/
7050/1850/1870N/5040/5050/
5070N/5140/5150D/5170DN
/
6050/6050D/6050DN/8050N/2070N /
5240/5250DN/5270DN/5280DW/
2140/2150N/2170W/5340D/5350
DN/5370DW/5380DN/2130/2240
D/2250DN/2270DW)
1 to 7 (HL-4140CN/
4150CDN/4570CDW/5440D/545
0DN/5470DW/6180DW/S7000D
N/3140CW/3150CDW/3150CDN/
3170CDW/L8250CDN/L8350CD
W(T)/L9200CDW(T))
XOFFSET Sets the X offset ( horizontal offset )
value. -500 to 500 dots (HL-1050/1070/
1250/1270N/1450/1470N/P2500/
1650/1670N/2460/7050/1850/
1870N/5040/5050/5070N/5140/
5150D/5170DN
/6050/6050D/
6050DN/8050N/2070N /5240/5250D
N/5270DN/5280DW/2140/2150N
/2170W/5340D/5350DN/5370D
W/5380DN/2130/2240D/2250DN
/2270DW /4140CN/
4150CDN/4570CDW/5440D/545
0DN/5470DW/6180DW/S7000D
N/3140CW/3150CDW/3150CDN/
3170CDW/1110/1111/1112/1118/
L8250CDN/L8350CDW(T)/L920
0CDW(T))
-104 to 500 dots (HL-3260N)
YOFFSET Sets the Y offset ( vertical offset ) value. -500 to 500 dots
AUTOCONT Auto Continue Mode ON or OFF
TIMEOUTEMU Sets the time-out value for automatic
emulation switching. 1 to 99 seconds
PRIORITY Sets the priority between EPSON or
IBM for automatic emulation switching. EPSON or IBM
HPFSEL ALL, LJ4 (HL-1650/1670N/
3260N/2460/7050/1850/1870N/
5040/5050/5070N/5140/5150D/
5170DN
/6050/6050D/6050DN/
8050N/2070N /5240/5250DN/5270
DN/5280DW/2140/2150N/2170
W/5340D/5350DN/5370DW/538
0DN/2250DN/2270DW /4140CN/
4150CDN/4570CDW/5440D/545
0DN/5470DW/6180DW/S7000D
N/3140CW/3150CDW/3150CDN/
3170CDW/L8250CDN/L8350CD
W(T)/L9200CDW(T))
AUTOFF Sets the auto FF setting to ON or OFF. ON or OFF
TIMEOUTFF Sets the timeout value for auto FF. 1 to 99 seconds
TIMEOUT Sets the timeout value for Automatic
interface switching 1 to 99 seconds
CDCCHIGH Sets the high-speed transfer mode of the
Centronics interface to ON or OFF. ON or OFF (HL-1050/1070/1250/
1270N/1450/1470N/P2500)
DTRCTRL Selects when DTR becomes low.
0 = the printer is turned off-line by the
SEL switch, the input buffer is full, or
when a printer error occurs. 0 to 2(HL-1050/1070/1250/
1270N/1450/1470N/P2500)
0 to 3(HL-1650/1670N/1850/
1870N/5040/5050/5070N/5140/