Edwards Signaling FireShield 10 Zone - Manual (Page 19)

Installation
FireShield Technical Reference Manual 2.9
3. Use JP1 to configure the FSDACT for attended or
unattended downloading:
• Attended: leave the JP1 wire intact
• Unattended: cut the JP1 wire
4. Install the dialer to the back of the circuit board. Align the
LCD display with the opening in the circuit board.
5. Secure the dialer to the circuit board with the two
machine screws provided.
6. Connect the power cable to J2 on the control panel.
7. Connect RJ31X/C31X jacks to the supplied cables.
8. Connect the telephone circuits as required.
Circuit board
Line 1
Line 2
To wall
phone jack
Phone cables
(supplied) RJ31 jacks
JP1 jumper wire
FSDACT installation and telephone circuit connection
The FSDACT is listed for use with the following DACRs
Receiver Models Formats
Ademco 685 EST 4/2*, Contact ID
FBII CP220 EST 4/2*, Contact ID
Osborne-Hoffman OH 2000 EST 4/2*, Contact ID
Radionics D6500 EST 4/2*
Silent Knight 9000 EST 4/2*
Sur-Gard MLR1, MLR2,
MCDI TLR, TLR+ EST 4/2*, Contact ID
* EST 4/2 is SIA DCS-02 P3 with the ability to transmit hexadecimal
event codes.
FCC Information
1. The dialer complies with Part 68 of the FCC rules. The dialer’s FCC
certification number and Ringer Equivalence Number (REN) is
displayed on the panel’s programming label and in this manual. This
information must be provided to the telephone company if requested.
2. Two FCC compliant telephone cords with 8-pin modular plugs at both
ends are supplied with the FSDACT. The dialer is designed to be
connected to the telephone network using the supplied cord and an
RJ31X or RJ38X jack, which must also comply with FCC Part 68 rules.
3. The REN is used to determine the maximum number of devices that may
be connected to a single telephone circuit. All telephone devices are
assigned a REN. The sum of the RENs for all connected devices may
not exceed five. The maximum REN may vary in some areas. Contact
the local telephone provider for more information.
4. If the dialer causes harm to the telephone network, the telephone
company will notify you an advance that temporary discontinuance of
service may be required. If advance notice is not practical, the telephone
company will notify you as soon as possible. You will also be advised of
your right to file a complaint with the FCC, if you believe it is
necessary.
5. The telephone company may make changes in its facilities, equipment,
operations, or procedures that could affect the operation of the dialer. If this
happens, the telephone company will provide advance notice in order for
you to make necessary modifications to maintain uninterrupted service.
6. If trouble is experienced with the dialer, for repair or warranty
information, contact the manufacturer at: (941) 739-4200. If the dialer is
causing harm to the telephone network, the telephone company may
request you disconnect the dialer until the problem is resolved.
7. No repairs may be performed on the dialer by the user.
8. The dialer can not be used on public coin phones or party line service
provided by the telephone company.
Industry Canada Information
NOTICE: This equipment meets the applicable Industry Canada Terminal
Equipment Technical Specifications. This is confirmed by the registration
number. The abbreviation, IC, before the registration number signifies that
registration was performed based on a Declaration of Conformity indicating
that Industry Canada technical specifications were met. It does not imply that
Industry Canada approved the equipment.
Before installing this equipment, users should ensure that it is permissible to
be connected to the facilities of the local telecommunications company. The
equipment must also be installed using an acceptable method of connection.
The customer should be aware that compliance with the above conditions may
not prevent degradation of service in some situations.
Repairs to certified equipment should be coordinated by a representative
designated by the supplier. Any repairs or alterations made by the user to this
equipment, or equipment malfunctions, may give the telecommunications
company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground
connections of the power utility, telephone lines, and internal metallic water
pipe system, if present, are connected together. This precaution may be
particularly important in rural areas.
Caution: Users should not attempt to make connections themselves, but
should contact the appropriate electric inspection authority, or electrician, as
appropriate.
NOTICE: The Ringer Equivalence Number (REN) for this terminal
equipment is 0.1. The REN assigned to each terminal equipment provides an
indication of the maximum number of terminals allowed to be connected to a
telephone interface. The termination on an interface may consist of any
combination of devices subject only to the requirement that the sum of the
Ringer Equivalence Numbers of all the devices does not exceed five.