Teledyne GFC-7001T - Trace CO Analyzer - Manual (Page 16)

Table of ContentsTeledyne API – Model T300/T300M CO Analyzer
Teledyne Analytical Instruments xvi
LIST OF FIGURES
Figure 3-1:
Front Panel Layout ....................................................................................................................... 35
Figure 3-2: Display Screen and Touch Control .............................................................................................. 36
Figure 3-3: Display/Touch Control Screen Mapped to Menu Charts ............................................................. 38
Figure 3-4: Rear Panel Layout ....................................................................................................................... 39
Figure 3-5: Internal Layout – GFC7001T ....................................................................................................... 41
Figure 3-6: Internal Layout – GFC7001TM .................................................................................................... 42
Figure 3-7: Optical Bench Layout (shorter bench, GFC7001TM, shown) ...................................................... 43
Figure 3-8: Analog In Connector .................................................................................................................... 45
Figure 3-9: Analog Output Connector ............................................................................................................ 46
Figure 3-10: Current Loop Option Installed on Motherboard ........................................................................... 47
Figure 3-11: Status Output Connector ............................................................................................................. 48
Figure 3-12: Control Input Connector ............................................................................................................... 50
Figure 3-13: Concentration Alarm Relay .......................................................................................................... 51
Figure 3-14: Rear Panel Connector Pin-Outs for RS-232 Mode ...................................................................... 54
Figure 3-15: Default Pin Assignments for CPU COM Port connector (RS-232) .............................................. 55
Figure 3-16: Jumper and Cables for Multidrop Mode ....................................................................................... 57
Figure 3-17: RS-232-Multidrop PCA Host/Analyzer Interconnect Diagram ..................................................... 58
Figure 3-18: Pneumatic Connections–Basic Configuration–Using Bottled Span Gas ..................................... 61
Figure 3-19: Pneumatic Connections–Basic Configuration–Using Gas Dilution Calibrator ............................. 61
Figure 3-20: GFC7001T/GFC7001TM Internal Gas Flow ................................................................................ 62
Figure 3-21: Pneumatic Connections – Option 50A: Zero/Span Calibration Valves ........................................ 63
Figure 3-22 Internal Pneumatic Flow OPT 50A – Zero/Span Valves .............................................................. 64
Figure 3-24: Internal Pneumatic Flow – Zero/Span/Shutoff Valves (Opt 50B) ................................................ 65
Figure 3-25: Pneumatic Connections – Zero Scrubber/Pressurized Span Calibration Valves (Opt 50E) ....... 66
Figure 3-26: Internal Pneumatic Flow Zero Scrubber/Pressurized Span Calibration Valves (Opt 50E) .......... 68
Figure 3-27: Pneumatic Connections – Option 50H: Zero/Span Calibration Valves ....................................... 69
Figure 3-28: Internal Pneumatic Flow OPT 50H – Zero Scrubber/Ambient Span ........................................... 70
Figure 3-29: Zero/Span Calibration Procedure ................................................................................................ 80
Figure 4-1: Front Panel Display ...................................................................................................................... 85
Figure 4-2: Viewing GFC7001T/GFC7001TM Test Functions ....................................................................... 87
Figure 4-3: Viewing and Clearing GFC7001T/GFC7001TM WARNING Messages ...................................... 90
Figure 5-1: Analog Output Connector Pin Out ............................................................................................... 95
Figure 5-2: COMM– Machine ID ..................................................................................................................110
Figure 5-3: Accessing the Analog I/O Configuration Submenus ..................................................................118
Figure 5-4: Setup for Checking / Calibrating DCV Analog Output Signal Levels .........................................125
Figure 5-5: Setup for Checking / Calibration Current Output Signal Levels Using an Ammeter ..................127
Figure 5-6: Alternative Setup Using 250Ω Resistor for Checking Current Output Signal Levels ................129
Figure 5-7. DIAG – Analog Inputs (Option) Configuration Menu .................................................................133
Figure 6-1: COM1[2] – Communication Modes Setup .................................................................................141
Figure 6-2: COMM Port Baud Rate ..............................................................................................................142
Figure 6-3: COMM – COM1 Test Port ..........................................................................................................142
Figure 6-4: COMM – LAN / Internet Manual Configuration ..........................................................................145
Figure 6-5 : COMM – LAN / Internet Automatic Configuration (DHCP) ........................................................146
Figure 7-1: Default DAS Channel Setup ......................................................................................................167
Figure 7-2: APICOM Remote Control Program Interface .............................................................................181
Figure 7-3: APICOM User Interface for Configuring the DAS ......................................................................182
Figure 7-4: DAS Configuration Through a Terminal Emulation Program .....................................................183
Figure 9-1: Pneumatic Connections – Basic Configuration – Using Bottled Span Gas ...............................196
Figure 9-2: Pneumatic Connections – Basic Configuration – Using Gas Dilution Calibrator .......................196
Figure 9-3: Pneumatic Connections – Option 50A: Ambient Zero/Ambient Span Calibration Valves .........201
Figure 9-4: Pneumatic Connections – Option 50B: Ambient Zero/Pressurized Span Calibration Valves ...202
Figure 9-5: Pneumatic Connections – Option 50H: Zero/Span Calibration Valves .....................................202