Teledyne GFC-7001T - Trace CO Analyzer - Manual (Page 10)

Table of ContentsTeledyne API – Model T300/T300M CO Analyzer
Teledyne Analytical Instruments x
3.4. Startup, Functional Checks, and Initial Calibration ...................................................................................... 72
3.4.1. Startup .................................................................................................................................................... 72
3.4.2. Warning Messages ................................................................................................................................ 72
3.4.3. Functional Checks ................................................................................................................................. 74
3.4.4. Initial Calibration .................................................................................................................................... 75
3.4.4.1. Interferents for CO Measurements ................................................................................................. 76
3.4.4.2. Initial Calibration Procedure ........................................................................................................... 76
3.4.4.3. O
2
Sensor Calibration Procedure ................................................................................................... 81
3.4.4.4. CO
2
Sensor Calibration Procedure ................................................................................................ 81
PART II OPERATING INSTRUCTIONS .................................................................................. 83
4. OVERVIEW OF OPERATING MODES ............................................................................... 85
4.1. Sample Mode ............................................................................................................................................... 86
4.1.1. Test Functions ....................................................................................................................................... 86
4.1.2. Warning Messages ................................................................................................................................ 88
4.2. Calibration Mode .......................................................................................................................................... 90
4.3. Setup MODE ................................................................................................................................................ 91
4.3.1. Password Security ................................................................................................................................. 91
4.3.2. Primary Setup Menu .............................................................................................................................. 91
4.3.3. Secondary Setup Menu (SETUP>MORE) ............................................................................................. 92
5. SETUP MENU 93
5.1. SETUP  CFG: Configuration Information ................................................................................................. 93
5.2. SETUP  ACAL: Automatic Calibration ...................................................................................................... 94
5.3. SETUP DAS: Internal Data Acquisition System ....................................................................................... 94
5.4. SETUP  RNGE: Analog Output Reporting Range Configuration ............................................................. 94
5.4.1. Analog Output Ranges for CO Concentration ....................................................................................... 94
5.4.2. Physical Range vs Analog Output Reporting Ranges ........................................................................... 95
5.4.3. Reporting Range Modes: Single, Dual, Auto Ranges ........................................................................... 96
5.4.3.1. SINGLE Range Mode (SNGL) ....................................................................................................... 98
5.4.3.2. DUAL Range Mode (DUAL) ........................................................................................................... 99
5.4.3.3. AUTO Range Mode (AUTO) ........................................................................................................101
5.4.4. Range Units .........................................................................................................................................103
5.4.5. Dilution Ratio (Option) ..........................................................................................................................104
5.5. SETUP  PASS: Password Protection .....................................................................................................105
5.6. SETUP  CLK: Setting the Internal Time-of-Day Clock and Adjusting Speed .........................................108
5.6.1.1. Setting the Internal Clock’s Time and Day ...................................................................................108
5.6.1.2. Adjusting the Internal Clock’s Speed ............................................................................................108
5.7. SETUP Comm: Communications Ports .................................................................................................110
5.7.1. ID (Machine Identification) ...................................................................................................................110
5.7.2. INET (Ethernet) ....................................................................................................................................110
5.7.3. COM1 and COM2 (Mode, Baud Rate and Test Port) ..........................................................................110
5.8. SETUP VARS: Variables Setup and Definition ......................................................................................111
5.9. SETUP Diag: Diagnostics Functions ......................................................................................................112
5.9.1. Signal I/O .............................................................................................................................................115
5.9.2. Analog Output ......................................................................................................................................116
5.9.3. Analog I/O Configuration ......................................................................................................................116
5.9.3.1. Analog Output Voltage / Current Range Selection .......................................................................119
5.9.3.2. Analog Output Calibration ............................................................................................................121
5.9.3.3. Enabling or Disabling the AutoCal for an Individual Analog Output .............................................121
5.9.3.4. Automatic Calibration of the Analog Outputs ...............................................................................122
5.9.3.5. Individual Calibration of the Analog Outputs ................................................................................124
5.9.3.6. Manual Calibration of the Analog Outputs Configured for Voltage Ranges .................................125
5.9.3.7. Manual Adjustment of Current Loop Output Span and Offset .....................................................127
5.9.3.8. Turning an Analog Output Over-Range Feature ON/OFF ...........................................................130
5.9.3.9. Adding a Recorder Offset to an Analog Output ............................................................................131
5.9.3.10. AIN Calibration ...........................................................................................................................132