Luminex 100 IS User Manual, Version 2.3 User Manual
Lum/nex
Table of contents
Document Outline
- Contents
- Introduction
- Safety
- The System
- Theory of Operation
- Hardware
- xMAP Technology Reagents
- Required Laboratory Reagents
- Luminex 100 IS 2.3 Software
- Luminex 100 IS Performance Specification
- Luminex 100 Analyzer General
- Luminex XYP Instrument General
- Luminex SD System General
- PC Specifications
- System Overview
- Basic Concepts
- Using Luminex 100 IS 2.3 Software
- Main Window
- Secondary Windows
- Commands
- Acquire Patient
- Add Batch
- Alcohol Flush
- Autoscale
- Autosize
- Backflush
- CAL1
- CAL2
- Cancel (Command)
- Cancel All
- Change Lot
- CON1
- CON2
- Connect to Instrument
- Create New Multi-Batch
- Delete Batch
- Density/Decaying
- Display Confirmation Screens
- Disconnect from the Instrument
- Drain
- Eject/Retract
- Enable Raw Data Storage
- Export Batch Data
- Export CAL
- Export CON
- Export Data
- Help
- Import Calibration
- Import Control
- Import Template
- Insert
- Invalidate Control
- Invalidate Standard
- Load Patient List
- Log/Linear
- Maximize/Minimize
- Next Test
- New Advanced Batch
- New Batch
- New CAL Targ.
- New CON Targ.
- New Lot
- Open Batch
- Open Help
- Open Incomplete Batch
- Open Multi-Batch
- Pause
- Previous Test
- Prime
- Print Batch Worklist
- Print Report
- Recalc
- Replay Batch
- Report Raw Fluorescence
- Resume
- Sample Probe Down
- Sanitize
- Save and Load
- Save Only
- Self Diagnostics
- Show Bead
- Single Step
- Skip [wells]
- Soak
- Start Analysis
- Start (Plate)
- Statistics
- Test Sort Orders
- Validate Control
- Validate Standard
- View Batch Data
- Warmup
- Wash
- Zoom
- Procedures
- Using the Online Help
- Setting Software Options
- Setting up the Favorites List
- Startup Procedures
- Calibration Procedures
- Batch Setup Procedures
- Importing Templates
- Create a New Batch
- Open a Batch
- Copying and Exporting Batch Data
- Clear a Batch from the System
- Replay a Batch
- Delete a Batch
- Create a Multi- Batch
- Open a Multi- Batch
- Process Multiple Plates
- Re-Run or Recover Incomplete Batch
- Scan in Samples With a Barcode Reader
- Add a Patient List
- Edit a Patient List
- Assign Sample Dilution Factors
- Create a New Advanced Batch
- Managing Assay Lots
- Analyzing Batches and Multi-Batches
- Running Reports and Analyses
- Database Management Procedures
- Maintenance Procedures
- Daily Shutdown Procedures
- Maintenance and Cleaning
- Troubleshooting
- Product Numbers
- Glossary
- Luminex 100 IS System Installation
- Overview
- Luminex 100 IS System Setup
- Connect the Luminex 100 analyzer and Luminex XYP to the PC
- Install the Luminex XYP Instrument Sample Probe
- Power On System Components
- Accept the Luminex 100 IS 2.3 Software License Agreement
- Adjust the Sample Probe Vertical Height
- Install the Luminex XYP Instrument Reservoir
- Calibrate and Verify the System
- Install the SD System
- Install the Luminex XYP Instrument Heater Block
- Luminex 100 IS 2.3 Software Installation
- Luminex 100 IS 2.3 Firmware Installation
- Network Installation Advisory
- Prepare System for First Use
- Installation Drawing
- Output.CSV