Mocomtech CRS-300 - Manual (Page 196)

CRS-300 1:10 Redundancy Switch Revision 16
Front Panel Operation MN/CRS300.IOM
7–16
The three-letter instruction code is indicated also to assist decoding the following problem
parameters:
► For the CDM-600L modem, the code is the hex value of the position of the problem
parameter within the MGC configuration code.
00 NO ERROR 01 TFQ Tx Frequency
09 TDR Tx Data Rate 12 TFT Tx FEC Type
13 TRS Tx Reed Solomon type 14 TCR Tx FEC Code Rate
15 TMD Tx Modulation 16 TSI Tx Spectrum Inversion
17 TSC Tx Scrambler state 18 TPL Tx Power Level
1C AUP AUPC enable 1D APP AUPC parameters
23 TCK Tx Clock source 24 TXO Tx Carrier state
25 TIT Tx Interface Type 26 TTC Tx Ternary Code
27 TFM Tx Framing Mode 28 TIP Tx IF Impedance
29 RFQ Rx Frequency 31 RDR Rx Data Rate
3A RFT Rx FEC Type 3B RRS Rx Reed Solomon type
3C RCR Rx FEC Code Rate 3D RMD Rx Modulation
3E RSI Rx Spectrum Inversion 3F RDS Rx DeScrambler state
40 RSW Rx Sweep Width 42 RCK Rx Clock source
43 EBA EbNo Alarm point 47 RBS Rx Buffer Size
4C RIT Rx Interface Type 4D RTC Rx Ternary Code
4E RFM Rx Framing Mode 4F RIP Rx IF Impedance
50 EFM Unit EDMAC Mode 51 ESA EDMAC Slave Address
55 TST Unit Test Mode 56 MSK Unit Alarm Mask
5C EFR External Freq Ref 5D SSI Statistics Sampling Interval
5E RTE Rx Terrestrial Alarm Enable 5F TTA Tx Terrestrial Alarm Mask
60 ODU ODU comms Enable 61 TBA Tx Backward Alarms
65 RBA Rx Backward Alarms 69 TVL Tx audio Volume
6D RVL Rx audio Volume 71 DTY Drop Type
72 ITY Insert Type 73 TET Tx ESC Type - 64k or 2 audio
74 RET Rx ESC Type - 64k or 2 audio 75 ITD Invert Tx Data
76 IRD Invert Rx Data
► For the CDM-570L modem, the code is the decimal number indicating the problem
parameter within its MGC configuration code:
00 NO ERROR 01 ITF Interface
02 LBO T1 Line Build-Out 03 FRM Framing mode
04 TFQ Tx Frequency 05 TFT Tx FEC Type
06 TMD Tx Modulation 07 TCR Tx FEC Code Rate
08 TDR Tx Data Rate 09 TSI Tx Spectrum Invert
10 TSC Tx Scrambler state 11 TPL Tx Power Level
12 TCK Tx Clock 13 TDI Tx Data Invert
14 TXO Tx Carrier State 15 AUP AUPC enable
16 APP AUPC parameters 17 WUD Warm-Up Delay
18 RFQ Rx Frequency 19 RFT Rx FEC Type
20 RMD Rx Modulation 21 RCR Rx FEC Code Rate
22 RDR Rx Data Rate 23 RSI Rx Spectrum Invert
24 RDS Rx DeScrambler state 25 RDI Rx Data Invert
26 RSW Rx Sweep Width 27 EBA Eb/No Alarm point
28 RBS Rx Buffer Size/enable 29 ERF External Reference setting
30 EFM EDMAC Framing mode 31 ESA EDMAC Slave Address range
32 TST Test mode 33 MSK Alarm Masks
34 RTS Request-To-Send control 35 SSI Statistics Sample Interval