KEPCO KLN 750W Series, Firmware Version 1.60 to 1.6x - Manual (Page 80)

B-6
KLN 750W 032614
B.29 SOURce:VOLTage:PROTection:LEVel COMMAND
SOUR:VOLT:PROT:LEV
Syntax: Short Form: SOUR:VOLT:PROT:LEV { MIN | MAX }
Long Form: SOURce:VOLTage:PROtection:LEVel { MIN | MAX }
Argument: is a value in the range from 0% to 110% of rated voltage.
MIN is the value programmed for output voltage (SOUR:VOLT)
MAX is 110% of rated voltage of unit
Description: Sets the overvoltage protection (OVP) value (in volts). OVP values set using this command
are in effect once the unit is returned to local operation. SOUR:VOLT:PROT:LEV MAX sets OVP to
maximum value: 110% of rated voltage. SOUR:VOLT:PROT:LEV MIN sets OVP to the same value
as programmed voltage (SOUR:VOLT). *RST sets SOUR:VOLT:PROT:LEV to maximum value.
Example: SOURce:VOLTage:PROtection:LEVel 36 sets the overvoltage protection level to 36V. This is the
maximum overvoltage protection value if the unit is a 30V model. SOUR:VOLT:PROT:LEV MIN
sets OVP to the same value programmed for output voltage (SOUR:VOLT).
B.30 SOURce:VOLTage:PROTection:LEVel? QUERY
SOUR:VOLT:PROT:LEV?
Syntax: Short Form: SOUR:VOLT:PROT:LEV? Long Form: SOURce:VOLTage:PROtection:LEVel?
Description: Indicates programmed lower limit for output voltage (in volts).
Return Format:
Example:
SOURce:VOLTage:PROtection:LEVel? returns 4.40000E+01 to indicate overvoltage protection
level is programmed to 44V.
B.31 SYSTem:BEEP COMMAND
SYST:BEEP
Syntax: Short Form: SYST:BEEP { ON | OFF | 1 | 0 }
Long Form: SYSTem:BEEP { ON | OFF | 1 | 0 }
Description: Sets the audible beep each time a front panel key is pressed to on or off.
Argument: or 1 enables audible beep
or 0 disables audible beep
Example: SYSTem:BEEP 1 turns on the audible beep.
B.32 SYSTem:BEEP? QUERY
SYST:BEEP?
Syntax: Short Form: SYST:BEEP? Long Form: SYSTem:BEEP?
Description: Indicates whether audible beep is on or off. Returns 1 to indicate the beep is on, 0 to indicate
beep is off.
Return Format: { 1 | 0 }
Example:
SYSTem:BEEP? returns 1 (audible beep is enabled).
B.33 SYSTem:COMMunicate:LAN:DHCP COMMAND
SYST:COMM:LAN:DHCP
Syntax: Short Form: SYST:COMM:LAN:DHCP { ON | OFF | 1 | 0 }
Long Form: SYSTem:COMMunicate:LAN:DHCP { ON | OFF | 1 | 0 }
Description: Allows the IP address to either be assigned from the DHCP server (on) or assigned manu-
ally (static IP Address) by the user (off).
Argument: or 1 enables DHCP
or 0 disables DHCP
Example: SYST:COMM:LAN:DHCP ON assigns the DHCP server to assign the IP address.
B.34 SYSTem:COMMunicate:LAN:DHCP? QUERY
SYST:COMM:LAN:DHCP?
Syntax: Short Form: SYST:COMM:LAN:DHCP? Long Form: SYSTem:COMMunicate:LAN:DHCP?
Description: Indicates whether DHCP is on (enabled) or off (disabled). Returns 1 to indicate the DHCP is
on, 0 to indicate DHCP is off.
Return Format: { 1 | 0 }
Example:
SYST:COMM:LAN:DHCP? returns 1 (DHCP is enabled).