Yaskawa Sigma-5 User Manual: Operation of Digital Operator User Manual

Page 130

3 Utility Function Mode

3.2.33 Online Vibration Monitor (Fn207)

3-96

Press the

Key for at least one sec-

ond to start vibration detection. The

Key must be pressed until “Measure”

flashes on the display. After this message
appears, the

Key does not have to

be pressed and the detection continues

automatically.

When the vibration detection has com-

pleted, “Measure” stops flashing and the

detection processing ends automatically.

When the detection processing has com-

pleted normally, the vibrations with three

largest peak values in vibration frequency

are displayed for F1, F2, and F3.

Notes:

• Press the

Key to quit the online

vibration monitor function. The display

returns to the main menu of the utility

function mode.

• A detected frequency can be displayed.

For a vibration with undetectable peak

frequency, “----” is displayed. If no fre-

quency was detected, “----” is displayed

for F1, F2, and F3.

• If the frequency could not be success-

fully detected, “NO MONITOR” is dis-

played.

After the detection has normally com-
pleted, press the

Key. The optimum

frequency (time constant) of notch filter or

torque reference filter for F1 is set auto-

matically. At the same time, the parameter

Pn409 is updated for a notch filter, or the

parameter Pn401 is updated for a torque

reference filter.

After the setting is successfully completed,

“DONE” flashes.

Press the

Key.

The display returns to the main menu of the

utility function mode.

(cont’d)

Step

Display after Operation

Keys

Operation

㧾㨁㧺ޓޓޓ㧙㨂㧙㧹㧻㧺㧵㨀㧻㧾㧙
㧹㨑㨍㨟㨡㨞㨑
㧲㧝㧩㧙㧙㧙㧙
㧲㧞㧩㧙㧙㧙㧙
㧲㧟㧩㧙㧙㧙㧙

㧾㨁㧺ޓޓޓ㧙㨂㧙㧹㧻㧺㧵㨀㧻㧾㧙
㧹㨑㨍㨟㨡㨞㨑
㧲㧝㧩ޓ㧜㧤㧡㧜㨇㧴㨦㨉
㧲㧞㧩ޓ㧝㧢㧜㧜㨇㧴㨦㨉
㧲㧟㧩ޓ㧜㧞㧞㧡㨇㧴㨦㨉

㧰㧻㧺㧱ޓޓ㧙㨂㧙㧹㧻㧺㧵㨀㧻㧾㧙
㧿㧱㨀㨀㧵㧺㧳ޓ㧰㧻㧺㧱
㧲㧝㧩ޓ㧜㧤㧡㧜㨇㧴㨦㨉
㧲㧞㧩ޓ㧝㧢㧜㧜㨇㧴㨦㨉
㧲㧟㧩ޓ㧜㧞㧞㧡㨇㧴㨦㨉

㧾㨁㧺ޓޓޓޓ㧙㧲㨁㧺㧯㨀㧵㧻㧺㧙
㧲㨚㧞㧜㧢㧦㧱㨍㨟㨥ޓ㧲㧲㨀

㧲㨚㧜㧜㧝㧦㧶㧻㧳

㧲㨚㧜㧜㧜㧦㧭㨘㨙ޓ㧴㨕㨟㨠㨛㨞㨥

㧲㨚㧞㧜㧣㧦㨂㧹㨛㨚㨕㨠㨛㨞