Ivoclar Vivadent SR Adoro - Manual (Page 7)

7
Warning
sR Adoro is intended for dental-lab use only. Contact of unpoly-
merized material (pastes) with the skin or eyes must be prevented.
skin contact of unpolymerized material may have a slight irritating
effect and may lead to a sensitization against methacrylates.
many commercial medical gloves do not provide protection
against the sensitizing effect of methacrylates. Do not inhale
grinding dust. the safety notes on the individual primary packages
and labels have to be observed.
General note
Failure to observe the stipulated contraindications and processing
instructions may lead to clinical failure.
Side effects
there are no known side effects to date. in individual cases
allergic reactions may occur. if a patient is known to be allergic to
any of the ingredients, sR Adoro must not be used.
Storage instructions
– store sR Link in the refrigerator (2–8 °C/36–46 °F).
– store sR Adoro layering materials and sR Adoro thermo Guard
at 12–28°C/54–82 °F.
– Close syringes immediately after usage (exposure to light causes
premature polymerization).
– Reseal sR Adoro thermo Guard immediately after use
(exposure to light causes premature polymerization).
– protect the materials from direct sunlight.
– Do not use the products after the indicated expiration date.
– Keep material out of children’s reach.
How to clean SR Adoro restorations
incorrect use of the ultrasound cleaning liquid may dissolve the
composite surface due to the high aggressiveness of the liquids.
therefore, alkaline cleaners with a pH value higher than 8 should
not be used.
Composition
– SR Adoro layering materials
(Cervical, Dentin, Deep Dentin, incisal, transpa, impulse and
Gingiva materials)
Dimethacrylate (17–19 wt.%); copolymer and silicon dioxide
(82–83 wt.%). Additional contents are catalysts, stabilizers and
pigments (<1 wt%).
the total content of inorganic fillers is 64–65 wt.%/46–47 vol.%.
particle size 10-100 nm.
– SR Adoro Liner
Dimethacrylate (48 wt.%); barium glass filler and silicon dioxide
(51 wt.%). Additional contents are catalysts, stabilizers and
pigments (<1 wt%).
– SR Adoro Opaquer
Dimethacrylate (> 55 wt.%); inorganic fillers (43 wt.%).
Additional contents are catalysts, stabilizers and pigments
(< 2.5 wt%).
– SR Adoro Stains
Dimethacrylate (47–48 wt.%); copolymer and silicon dioxide
(49–50 wt.%).
Additional contents are catalysts, stabilizers and pigments
(2–3 wt%).
– SR Adoro Add-On
Dimethacrylate (16–17 wt.%); copolymer and silicon dioxide
(82–83 wt.%). Additional contents are catalysts, stabilizers and
pigments (<1 wt%).
– SR Model Separator
polyglycol, polyethylene glycol in a water/alcohol solution.
– SR Link
Dimethacrylate, phosphate ester, solvent and benzoyl peroxide.
– SR Gel
Glycerine, silicon dioxide and aluminium oxide.
– SR Adoro Thermo Guard
Diethylene glycol, water, inorganic fillers, synthetic fibres.
– SR Retention Adhesive
Copolymer, resin and softener (30 wt.%) dissolved in acetone
(70 wt.%).
– SR Micro Retention Beads 200–300 microns
– SR Macro Retention Beads 400–600 microns
Copolymer (99.5 wt.%) and titanium dioxide (0.5 wt.%).
– SR Composiv
Dimethacrylate; silicon dioxide (16–17 wt.%) Additional contents
are catalysts, stabilizers and pigments (<2.5 wt.%).
– Universal Polishing Paste
emulsion of aluminium oxide, ammonium oleate, petroleum
distillate and water.