TeeJet TASC-6600 User Manual
Page 3
III
TASC-6000, 6300, 6600
98-05010
Rev. - 1
TASC MANUAL - CHANGE LOG ....................................................................................................................................... II
TABLE OF CONTENTS ....................................................................................................................................................... III
1.0 SWITCHES AND CONTROLS ..................................................................................................................................... 1-1
1.1 POWER SWITCH .................................................................................................................................................. 1-1
1.2 MODE SELECTOR OPERATE/SET- UP SWITCH ................................................................................................. 1-1
1.3 INC/DEC SWITCH ................................................................................................................................................. 1-1
1.4 DISPLAY SELECTOR ............................................................................................................................................ 1-1
1.4.1 DISPLAY SELECTOR FUNCTIONS IN OPERATE MODE .......................................................................... 1-2
1.4.2 DISPLAY SELECTOR FUNCTIONS IN SET UP MODE .............................................................................. 1-3
1.5 BOOM SECTION “ON/OFF” INDICATORS ........................................................................................................ 1-4
1.6 INJECTION PUMP SWITCHES (TASC 6300 and 6600 only) ............................................................................... 1-4
1.7 STATUS SWITCH ................................................................................................................................................. 1-4
1.8 GROUND SPEED OVERRIDE SWITCH ................................................................................................................ 1-5
2.0 CALIBRATION AND SET UP ...................................................................................................................................... 2-1
2.1 ENGLISH AND METRIC UNITS ........................................................................................................................... 2-1
2.1.1 UNITS FOR EACH POSITION .................................................................................................................... 2-1
2.1.2 CHANGING UNITS ..................................................................................................................................... 2-1
2.2 PERISTALTIC AND NON-PERISTALTIC INJECTION PUMP MODES ................................................................ 2-1
2.3 SETTING APPLICATION RATES ......................................................................................................................... 2-2
2.3.1 SETTING CARRIER APPLICATION RATE ................................................................................................. 2-2
2.3.2 SETTING CHEMICAL APPLICATION RATE ............................................................................................. 2-2
2.3.3 SETTING ALTERNATE CHEMICAL APPLICATION RATE ...................................................................... 2-3
2.4 SETTING THE % RATE CHANGE OF THE CHEMICAL INJECTION PUMPS & THE CARRIER ........................ 2-3
2.5 SETTING BOOM WIDTHS ................................................................................................................................... 2-4
2.6 FLOW METER CALIBRATION ............................................................................................................................ 2-4
2.6.1 TYPICAL FLOWMETER CALIBRATION NUMBERS (for water) .............................................................. 2-5
2.6.2 FLOW METER CALIBRATION PROCEDURE ............................................................................................ 2-5
2.7 DISTANCE CALIBRATION, GROUND SPEED SENSOR ...................................................................................... 2-6
2.7.1 GENERAL CONSIDERATIONS AND INITIAL CALIBRATION NUMBERS .............................................. 2-6
2.7.2 DISTANCE CALIBRATION PROCEDURE .................................................................................................. 2-7
2.8 INJECTION PUMP CALIBRATION (TASC-6300 & 6600 ONLY) .......................................................................... 2-7
2.8.1 TYPICAL PUMP CALIBRATION NUMBERS, PC# .................................................................................... 2-8
2.8.2 PUMP CALIBRATION, FIELD PROCEDURE .............................................................................................. 2-8
2.8.3 ESTABLISHING THE “PRIME” VOLUME FOR EACH INJECTION PUMP .............................................. 2-10
2.9 SETTING THE "HOLD/CLOSE" RESPONSE OF THE FLOW CONTROL VALVE ............................................... 2-12
2.9.1 STATUS SWITCH ..................................................................................................................................... 2-12
2.9.2 ALL BOOMS "OFF" .................................................................................................................................. 2-13
2.10 SETTING THE GROUND SPEED OVERRIDE "GSO" VALUE. ........................................................................... 2-13
2.11. SETTING AUTO POWER DOWN TIME ........................................................................................................... 2-14
2.12 REFLOW MODE ............................................................................................................................................... 2-14
2.12.1. DESCRIPTION ........................................................................................................................................ 2-14
2.12.2. REFLOW SET UP ................................................................................................................................... 2-15
2.12.3. ESTABLISHING THE REFLOW OPTION ............................................................................................... 2-15
2.12.4. CANCELLING THE REFLOW OPTION .................................................................................................. 2-15
2.12 OPERATING UNDER EXTERNAL RATE COMMANDS .................................................................................. 2-16
TABLE OF CONTENTS