Lenze E84Dxxxx - Manual (Page 85)

Lenze · Decentralised frequency inverter 8400 protec (EtherNet/IP™ option) · Communication Manual · DMS 3.0 EN · 07/2014 · TD17
85
12 Error messages
12.4 Mapping of Lenze device errors to DRIVECOM errors
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
xx.0123.00201 SD11: Speed limit - feedback system 67 0x7300 0x7300 Sensor
xx.0123.00205 SD3: Open circuit - feedback system 0x7300 0x7301 Tacho defective
xx.0125.00001 An01: AIN1_I < 4 mA 0xF000 0xF000 Additional functions
xx.0125.00002 An02: AIN2_I < 4 mA 0xF000 0xF000 Additional functions
xx.0125.00011 Io11: DigOut level 0xF000 0xF000 Additional functions
xx.0127.00002 CE04: MCI communication error 0x7000 0x7500 Communication
xx.0127.00003 Smr1: Module internal watchdog or trap 0x6100 0x6010 Software reset (watchdog)
xx.0127.00004 Smr2: Module Offline - no status or PDOs 0x7000 0x7500 Communication
xx.0127.00005 Smr3: Module timeout - one or more of PDOs
timeout
0x7000 0x7500 Communication
xx.0127.00006 Smr4: SDO access failure 0x6100 0x6100 Internal software
xx.0127.00015 CE0F: MCI control word 0xF000 0xF000 Additional functions
xx.0131.00000 CE4: CAN Bus Off 0x8000 0x8000 Monitoring
xx.0131.00006 CA06: CAN CRC error 0x8000 0x8000 Monitoring
xx.0131.00007 CA07: CAN Bus Warn 0x8000 0x8000 Monitoring
xx.0131.00008 CA08: CAN Bus Stopped 0x8000 0x8000 Monitoring
xx.0131.00011 CA0b: CAN Bus Live Time 0x8130 0x8000 Monitoring
xx.0131.00015 CA0F: CAN control word 0xF000 0x8000 Monitoring
xx.0135.00001 CE1: CAN RPDO1 0x8100 0x8100 Communication
xx.0135.00002 CE2: CAN RPDO2 0x8100 0x8100 Communication
xx.0135.00003 CE3: CAN RPDO3 0x8100 0x8100 Communication
xx.0135.00004 CP04: CAN RPDO4 0x8100 0x8100 Communication
xx.0140.00013 MCI1: Module missing/incompatible 0x7000 0x7000 Additional Modules
xx.0144.00001 PS01: No memory module 0x6300 0x6300 Date Set
xx.0144.00002 PS02: Par. set invalid 0x6300 0x6300 Date Set
xx.0144.00003 PS03: Par. set device invalid 0x6300 0x6300 Date Set
xx.0144.00004 PS04: Par. set device incompatible 0x6300 0x6300 Date Set
xx.0144.00007 PS07: Par. mem. module invalid 0x6300 0x6300 Date Set
xx.0144.00008 PS08: Par. device invalid 0x6300 0x6300 Date Set
xx.0144.00009 PS09: Par. format invalid 0x6300 0x6300 Date Set
xx.0144.00010 PS10: Memory module link invalid 0x5000 0x5000 Device Hardware
xx.0144.00031 PS31: Ident. error 0x6300 0x6300 Date Set
xx.0145.00001 dF01: Internal error 01 0x6100 0x6100 Internal software
xx.0145.00002 dF02: Internal error 02 0x6100 0x6100 Internal software
xx.0145.00003 dF03: Internal error 03 0x6100 0x6100 Internal software
xx.0145.00004 dF04: Internal error 04 0x6100 0x6100 Internal software
xx.0145.00005 dF05: Internal error 05 0x6100 0x6100 Internal software
xx.0145.00006 dF06: Internal error 06 0x6100 0x6100 Internal software
xx.0145.00007 dF07: Internal error 07 0x6100 0x6100 Internal software
xx.0145.00008 dF08: Internal error 08 0x6100 0x6100 Internal software
xx.0145.00009 dF09: Internal error 09 0x6100 0x6100 Internal software
xx.0145.00010 dF10: Internal error 10 0x6100 0x6100 Internal software
xx.0145.00014 dF14: SW-HW invalid 0x5530 0x6000 Device software
xx.0145.00024 dF18: BU RCOM error 0x6100 0x6100 Internal software
xx.0145.00025 dF25: CU RCOM error 0x6100 0x6100 Internal software
xx.0145.00033 dF21: BU watchdog 0x6100 0x6010 Software reset (watchdog)
xx.0145.00034 dF22: CU Watchdog 0x6100 0x6010 Software reset (watchdog)
xx.0145.00035 dF10: AutoTrip reset 0xF000 0xF000 Additional functions
xx.0145.00050 dF50: Retain error 0x6100 0x6100 Internal software
xx.0145.00051 dF51: CuCcr error 0x6100 0x6100 Internal software
Lenze error CAN DRIVECOM error
Error number
[32 bits]
Error message Emergency
Error Code
Error number
[hex]
Error message