Lenze E84Dxxxx - Manual (Page 84)

12 Error messages
12.4 Mapping of Lenze device errors to DRIVECOM errors
84
Lenze · Decentralised frequency inverter 8400 protec (EtherNet/IP™ option) · Communication Manual · DMS 3.0 EN · 07/2014 · TD17
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
12.4 Mapping of Lenze device errors to DRIVECOM errors
Via the instance attribute "FaultCode" of the Control Supervisor Object (41 / 0x29) ( 133) Lenze
device errors are output with the DRIVECOM error numbers.
The following tables show the assignment of the Lenze device errors to the "CAN Emergency Error
Codes" and DRIVECOM errors.

Reference manual / »Engineer« online help for Inverter Drives 8400 protec
Here you will find detailed information about the Lenze error messages listed in the
following table.
Lenze error CAN DRIVECOM error
Error number
[32 bits]
Error message Emergency
Error Code
Error number
[hex]
Error message
xx.0111.00002 Su02: One mains phase is missing 0x3000 0x3000 Voltage
xx.0111.00003 Su03: Too frequent mains switching 0x3000 0x3000 Voltage
xx.0111.00004 Su04: CU insufficiently supplied 0x3000 0x3000 Voltage
xx.0111.00005 Su05: IO Supply overload 0x3000 0x3000 Voltage
xx.0119.00000 OH4: Heat sink temp. > Switch-off temp. -5°C 0x4000 0x4000 Temperature
xx.0119.00001 OH1: Heatsink overtemperature 0x4000 0x4000 Temperature
xx.0119.00015 OH3: Motor temperature (X21) triggered 0x4000 0x4000 Temperature
xx.0119.00016 OH5: Brake res. temperature (X20) triggered 0x4000 0x4000 Temperature
xx.0119.00050 OC5: Ixt overload 0x2000 0x2000 Current
xx.0119.00052 OC9: Ixt overload - shutdown limit 0x2000 0x2000 Current
xx.0123.00001 OT1: Maximal torque reached 0x8300 0x8302 Torque limiting
xx.0123.00007 OC7: Motor overcurrent 0x2000 0x2000 Current
xx.0123.00014 OU: DC bus overvoltage 0x3100 0x3110 Mains overvoltage
xx.0123.00015 LU: DC bus undervoltage 0x3100 0x3120 Mains undervoltage
xx.0123.00016 OC1: Power section - short circuit 0x2000 0x2130 Short Circuit
xx.0123.00017 OC2: Power section - earth fault 0x2000 0x2120 Short to Earth
xx.0123.00030 OC10: Maximum current reached 0x2000 0x2000 Current
xx.0123.00031 OC17: Clamp sets pulse inhibit 0xF000 0xF000 Additional functions
xx.0123.00032 OS1: Maximum speed limit reached 0x8400 0x8402 Velocity Limiting
xx.0123.00033 OS2: Max. motor speed 0x8400 0x8400 Speed Controller
xx.0123.00057 ID1: Motor data identification error 0xF000 0xF000 Additional functions
xx.0123.00058 ID3: CINH motor data identification 0xF000 0xF000 Additional functions
xx.0123.00059 ID4: Error resistor identification 0xF000 0xF000 Additional functions
xx.0123.00060 ID7: Motor control does not match motor data 0xF000 0xF000 Additional functions
xx.0123.00065 OC12: I2xt overload - brake resistor 0xF000 0x7110 Brake Chopper
xx.0123.00071 OC11: Current clamp for too long (>1 sec) 0xF000 0xF000 Additional functions
xx.0123.00090 OC13: Maximum current for Fch exceeded 0xF000 0x2000 Current
xx.0123.00093 OT2: Speed controller output is limited 0xF000 0x7310 Speed
xx.0123.00094 FCH1: Switching frequency reduction 0x2000 0xF000 Additional functions
xx.0123.00095 FCH2: Maximum speed for Fchop 0xF000 0xF000 Additional functions
xx.0123.00096 OC14: Limitation direct-axis current controller 0xF000 0xF000 Additional functions
xx.0123.00097 OC15: Limitation cross current controller 0xF000 0xF000 Additional functions
xx.0123.00098 OC16: Limitation torque controller 0xF000 0xF000 Additional functions
xx.0123.00099 FC1: Limitation field controller 0xF000 0xF000 Additional functions
xx.0123.00105 OC6: I2xt overload - motor 0x2000 0x7120 Motor
xx.0123.00145 LP1: Motor phase failure 0x3000 0x3130 Phase Failure
xx.0123.00200 SD10: Speed limit - feedback system 12 0x7300 0x7300 Sensor