beautypg.com

Canon VB-M600VE User Manual

Page 50

background image

5

-6

IPv6

(1) [IPv6]

Set IPv6 use to [Disable] or [Enable].

(2) [Auto]

Select [Enabled] to set the address automatically or

[Disabled] not to set the address automatically.

(3) [IPv6 Address (Manual)]

Enter a fixed IPv6 address.

(4) [Prefix Length]

Enter a prefix length from 16 to 128 if [Disabled] is

specified in (2).

(5) [IPv6 Default Gateway Address]

Enter a default gateway address if [Disabled] is

specified in (2). Be sure to set when connecting the

camera to a different subnet from that of the viewer.

(6) [IPv6 Address (Auto)]

If [Enable] is specified in (1) and [Enabled] is

specified in (2), then the automatically acquired

address will be shown.

Note

In an environment where IPv6 cannot be used, if IPv6 is set to
[Enable] and auto is set to [Enabled], then the [IPv6 Address

(Auto)] field will display the link-local address only.

DNS

(1) [Name Server Address 1], [Name Server Address 2]

Enter the name server address you want to register.

To register only one address, keep the [Name Server

Address 2] field blank.

(2) [Host Name]

You can register the host name of the camera in the

name server.

Characters A to Z, a to z, 0 to 9, “-” (hyphen), “_”

(underscore) and “.” (period) may be used up to 63

(single-byte) characters in length.

(3) [Host Name Registration with DDNS]

Select [Enable] to register the entered name server

address and host name of the camera.

Note

• Use [Host Name Registration with DDNS] if the camera IP

Address Setting Method is [Auto (DHCP)] (p. 5-5). DNS server

registration settings must be set in advance. Contact your

System Administrator for the DNS server settings.

• If the name server address 1 is unavailable, the name server

address 2 will be accessed. However, the name server
address 2 must be set in advance.

Important

• Contact your System Administrator for the [IPv4 Address],

[Subnet Mask] and [IPv4 Default Gateway Address].

• The camera's IP address cannot be set to an IP address that

starts with 127., such as 127.0.0.1.

• If any of the [IPv4 Address], [Subnet Mask] or [IPv4 Default

Gateway Address] settings is wrong, network access may be
disabled. In this case, see “Performing Initial Settings for the

Camera” (p. 2-6) and use VB Initial Setting Tool to set the

address again.

• The camera may become inaccessible from the active web

browser if settings are changed in [IPv4 Address], [Subnet
Mask] or [IPv4 Default Gateway Address]. Check beforehand

the precautions in “Important” in “[Reboot Item] Setting Items

Requiring Rebooting” (p. 5-32).

• If [Auto (DHCP)] is selected as the IPv4 address setting

mode, the IPv4 address may not be assigned correctly in
certain environments, such as when a router is present

between the DHCP server and the camera. In this case,

assign a fixed IPv4 address from the [Manual] settings.

Important

• Contact your System Administrator for the [IPv6 Address

(Manual)], [Prefix Length] and [IPv6 Default Gateway
Address].

• The camera may become inaccessible from the active web

browser if settings are changed in [IPv6], [IPv6 Address

(Manual)], [Prefix Length] or [IPv6 Default Gateway Address].

Check beforehand the precautions in “Important” in “[Reboot
Item] Setting Items Requiring Rebooting
(p. 5-32).

Important

Do not use “_” (underscore) in [Host Name] in Internet Explorer 8/

9/10.

This manual is related to the following products: