KROHNE H250 M40 FOUNDATION FIELDBUS - Manual (Page 57)

OPERATION
4
57
H250 M40
www.krohne.com 02/2014 - 4001208201 - AD H250 M40 FF R02 en
Status RW Setting:
Good Non Cascade / Good Cascade / Uncertain / Bad Not
Connected / Bad / Bad No Comm with Last Useable Value
(LUV)
Bad Not Connected
Value RW Setting:
0: Forward / 1: Reverse
Forward
REV_FLOW2 REV_FLOW2 REV_FLOW2 REV_FLOW2
Reverse Flow 2 Reverse Flow 2 Reverse Flow 2 Reverse Flow 2
RW Indicates reverse flow when true.
Status RW Setting:
Good Non Cascade / Good Cascade / Uncertain / Bad Not
Connected / Bad / Bad No Comm with Last Useable Value
(LUV)
Bad Not Connected
Value RW Setting:
0: Forward / 1: Reverse
Forward
RTOTAL RTOTAL RTOTAL RTOTAL
Rejected Total Rejected Total Rejected Total Rejected Total
RW Indicates the Totalization of BAD or BAD + UNCERTAIN Inputs,
according to INTEG_OPTS.
0.0
SRTOTAL SRTOTAL SRTOTAL SRTOTAL
Snapshot of Snapshot of Snapshot of Snapshot of
Rejected Total Rejected Total Rejected Total Rejected Total
R The snapshot of RTOTAL, just before a reset. 0.0
SSP SSP SSP SSP
Snapshot of Snapshot of Snapshot of Snapshot of
Setpoint Setpoint Setpoint Setpoint
R The snapshot of TOTAL_SP. 0.0
STATUS_OPTS STATUS_OPTS STATUS_OPTS STATUS_OPTS
Status Option Status Option Status Option Status Option
RW Options which the user may select in the block processing of
status.
Uninitialized
Setting:
Uncertain if Man
STOTAL STOTAL STOTAL STOTAL
Snapshot of Total Snapshot of Total Snapshot of Total Snapshot of Total
R Indicates the Snapshot of OUT just before a reset. 0.0
TIME_UNIT1 TIME_UNIT1 TIME_UNIT1 TIME_UNIT1
Time Unit 1 Time Unit 1 Time Unit 1 Time Unit 1
RW Converts the rate time units in seconds. Uninitialized
Setting:
1: seconds / 2: minutes / 3: hour / 4: days
TIME_UNIT2 TIME_UNIT2 TIME_UNIT2 TIME_UNIT2
Time Unit 2 Time Unit 2 Time Unit 2 Time Unit 2
RW Converts the rate time units in seconds. Uninitialized
Setting:
1: seconds / 2: minutes / 3: hour / 4: days
TOTAL_SP TOTAL_SP TOTAL_SP TOTAL_SP
Total Setpoint Total Setpoint Total Setpoint Total Setpoint
RW The SP for a batch totalization. Not just SP because SP has PV
units and other special properties not used in this application.
0
Setting:
Positive or 0
UNIT_CONV UNIT_CONV UNIT_CONV UNIT_CONV
Unit Conversion Unit Conversion Unit Conversion Unit Conversion
RW Factor to convert the engineering units of input 2 into the
engineering units of input 1.
1.0
Setting:
Positive or not 0
UPDATE_EVT UPDATE_EVT UPDATE_EVT UPDATE_EVT
Update Event Update Event Update Event Update Event
R This alert is generated by any change to the static data.
Unacknowledged R A discrete enumeration which is set to "Unacknowledged"
when an alarm occurs, and set to "Acknowledged" by a write
from a human interface device or other entity which can
acknowledge that the alarm/event has been noticed.
Uninitialized
Setting:
Uninitialized / Acknowledged / Unacknowledged
Integrator Block
Parameter
DD Name Access Description
settings Initial
AD_H250_M40_FF_R02_en_4001208201_PRT.book Page 57 Friday, February 21, 2014 11:25 AM