GW Instek GRS-6000A Series - Manual (Page 6)

GRS-6052A/6032A OSCILLOSCOPE
USER MANUAL
⎯ ⎯
6
Sweep Time
0.2μs/DIV~0.5s/DIV, 20 steps selectable in 1-2-5
sequence, continuous variable control between steps
at least 1:2.5.
Accuracy ±3%, ±5% at ×5 and ×10 MAG, ±8% at ×20 MAG
Sweep Magnification Ч5, Ч10, Ч20 MAG
Maximum Sweep Time
(at MAG)
GRS-6052A:20ns/DIV (10ns/DIV uncalibrated)
GRS-6032A:50ns/DIV(10ns/DIV~40ns/DIV
uncalibrated.
HORIZONTAL
SYSTEM
(REAL TIME
mode)
ALT-MAG Function Available.
Trigger Modes AUTO, NORM, TV
Trigger Source VERT-MODE, CH1, CH2, LINE, EXT.
Trigger Coupling AC, HFR, LFR, TV-V(-), TV-H(-).
Trigger Slope “+” or “- ” polarity.
GRS-6052A
CH1,
CH2
VERT-
MODE
EXT
20Hz~5MHz 0.5 DIV 2.0 DIV 200mV
5MHz~40MHz 1.5 DIV 3.0 DIV 800mV
40MHz~50MHz 2.0 DIV 3.5 DIV 1V
GRS-6032A
CH1,
CH2
VERT-
MODE
EXT
20Hz~2MHz 0.5 DIV 2.0 DIV 200mV
2MHz~20MHz 1.5 DIV 3.0 DIV 800mV
20MHz~30MHz 2.0 DIV 3.5 DIV 1V
Trigger Sensitivity
TV sync pulse more than 1 DIV (CH1, CH2, VERT-
MODE) or 200mV (EXT).
External Trigger Input
Input impedance: Approx. 1MΩ//25pF(AC
coupling)
Max. input voltage: 400V (DC + AC peak) at 1kHz.
TRIGGER
SYSTEM
Hold-off Time Variable (Real Time Mode only).
Input X-axis : CH1, Y-axis : CH2
Sensitivity 1mV/DIV~20V/DIV.
Bandwidth X-axis: DC~500kHz (-3dB)
X-Y
OPERATION
(REAL TIME
mode)
Phase Difference 3°or less from DC to 50kHz
GRS-6052A/6032A OSCILLOSCOPE
USER MANUAL
⎯ ⎯
7
Acquisition Digitizer 8 bit ADC × 2
Max. Sampling Rate
500MS/s for equivalent time sampling.
100MS/s for normal sampling.
Acquisition Mode
Sample, Peak detect (>25ns), envelope, persistence,
average (2~256).
Storage Bandwidth(-
3dB)
Single shot: DC to 25MHz.
Repetitive : DC to 50MHz (GRS-6052A)
DC to 30MHz (GRS-6032A)
Dynamic Range ±5DIV.
Memory Length
Acquisition Memory
Save REF Memory
Display Memory 2k words/CH×2, 1k words/CH (equivalent)
1k words/CH×10 with back-up memory(REF 0~9)
1k words/CH×4 waveform (max.)
Sweep Time
Equivalent: 0.2μs/DIV ~ 0.5μs/DIV
Normal: 1μs/DIV ~ 0.1s/DIV
Roll Mode: 0.2s/DIV ~ 100s/DIV
Sweep Magnification Ч5, Ч10, Ч20
Max. Sweep Time 10ns/DIV
MAG Interpolation Dots, Linear
ALT-MAG Function Available
Operation Mode
Auto, Norm, Single, Single-roll, Roll, X-Y
Average (2 ~ 256), Run/Stop
Smoothing Function Dot Joint ON/OFF selectable
Pre-trigger
0 ~ 10DIV in 0.02DIV steps (at 5μs/DIV ~
0.1s/DIV)
X-Y Operation
X-axis: CH1, Y-axis: CH2
Storage Bandwidth : DC~50MHz (GRS-6052A)
DC~20MHz (GRS-6032A)
Display Resolution
H : 100 points/DIV
V : 25 points/DIV
X-Y: 25 × 25 points/DIV
DIGITAL
STORAGE
FUNCTIONS
Waveform
SAVE/RECALL
10 sets (REF0 ~ REF9) with back-up memory.
CH1 Signal Output
Voltage : approx. 20mV/DIV (with 50Ω
terminal.)
Bandwidth: 50Hz to at least 5MHz.
OUTPUT
SIGNAL
Calibrator Output
Voltage : 0.5V±3%,
Frequency: approx. 1kHz, square wave.