GW Instek GDS-1000-U Series Quick start guide - Manual

Digital Storage Oscilloscope
GDS-1000-U Series
QUICK START GUIDE
GW INSTEK PART NO. 82DS-1102UMA1
ISO-9001 CERTIFIED MANUFACTURER
S
AFETY INSTRUCTIONS
This section contains the basic safety symbols that may
appear on the accompanying user manual CD or on the
instrument. For detailed safety instructions and
precautions, please see the Safety Instructions chapter
in the user manual CD.
Safety Symbols
These safety symbols may appear in the user manual or
on the instrument.
Warning
Warning: Identifies conditions or
practices that could result in injury or
loss of life.
Caution
Caution: Identifies conditions or
practices that could result in damage
to the instrument or to other
properties.
DANGER High Voltage
Attention Refer to the Manual
Protective Conductor Terminal
Earth (ground) Terminal
Do not dispose electronic equipment
as unsorted municipal waste. Please
use a separate collection facility or
contact the supplier from which this
instrument was purchased.
Power Cord for the United Kingdom
When using the instrument in the United Kingdom,
make sure the power cord meets the following safety
instructions.
NOTE: This lead/appliance must only be wired by
competent persons.
WARNING: THIS APPLIANCE MUST BE EARTHED
IMPORTANT: The wires in this lead are coloured in
accordance with the following code:
Green/ Yellow: Earth
Blue: Neutral
Brown: Live (Phase)
As the colours of the wires in main leads may not correspond with
the coloured marking identified in your plug/appliance, proceed as
follows:
The wire which is coloured Green & Yellow must be connected to
the Earth terminal marked with either the letter E, the earth symbol
or coloured Green/Green & Yellow.
The wire which is coloured Blue must be connected to the terminal
which is marked with the letter N or coloured Blue or Black.
The wire which is coloured Brown must be connected to the terminal
marked with the letter L or P or coloured Brown or Red.
If in doubt, consult the instructions provided with the equipment or
contact the supplier.
This cable/appliance should be protected by a suitably rated and
approved HBC mains fuse: refer to the rating information on the
equipment and/or user instructions for details. As a guide, a cable of
0.75mm 2 should be protected by a 3A or 5A fuse. Larger conductors
would normally require 13A types, depending on the connection
method used.
Any exposed wiring from a cable, plug or connection that is engaged
in a live socket is extremely hazardous. If a cable or plug is deemed
hazardous, turn off the mains power and remove the cable, any
fuses and fuse assemblies. All hazardous wiring must be
immediately destroyed and replaced in accordance to the above
standard.
G
ETTING STARTED
The Getting started chapter introduces the
oscilloscope’s main features, appearance, and set up
procedure.
Main Features
Model name Frequency bandwidth Input channels
GDS-1052-U DC–50MHz (–3dB) 2
GDS-1072-U DC–70MHz (–3dB) 2
GDS-1102-U DC–100MHz (–3dB) 2
Performance • 250MSa/s real-time sampling rate
• 25GS/s equivalent-time sampling
rate
• 4k points record length
• Up to 10ns peak detection
• 2mV~10V vertical scale
• 1ns~50s time scale
Features • 5.7 inch color TFT display
• Saving and recalling setups and
waveforms
• 19 automatic measurements
• Multi-language menu (12
languages)
• Math operation: Addition,
Subtraction, FFT
• Data logging
• Go-NoGo testing
• Edge, Video, Pulse width triggers
Interface • USB 2.0 full-speed interface for
saving and recalling data
• Calibration output
• External trigger input
• USB B type (slave) interface for
remote control
Package Contents and Accessories
Standard Accessories
Part Number Description
82DS-112AUEA1 User Manual CD
82DS-1102UMA1 Quick Start Guide
(this document)
GTP-070A-4
for GDS-1052-U,
GDS-1072-U
Passive probe,
70MHz, 10x, 1x
GTP-100A-4
for GDS-1102-U
Passive probe,
100MHz, 10x, 1x
Region
Dependent
Power cord x1
Optional Accessories
Part Number Description
GTL-242 USB 2.0 Cable, type
A-B
GTL-110 Test Lead (BNC-
BNC)
GSC-006 Soft carry case
Display and Panel Overview
Display Overview
1
2 3 4
5
6 7 8 9
10
Description
1. Trigger position 2. Waveform position
3. Trigger status 4. Acquisition
5. Menu 6. Trigger condition
7. Frequency 8. Horizontal status
9. Vertical status 10. Waveform marker
Rear Panel
Description
1. Security lock slot 2. Fuse socket
3. Power cord socket 4. CAL output
5. USB B type port
Setting up the Oscilloscope
This section describes how to set up the oscilloscope
properly including adjusting the handle, connecting a
signal, adjusting the scale, and compensating the
probe. Before operating the oscilloscope in a new
environment, run these steps to make sure the
oscilloscope is functionally stable.
1. Pull both bases of the handle out slightly.
Front Panel
Description
1. LCD display 2. Function keys
3. Variable knob 4. Vertical position knob
5. VOLTS/DIV knob 6. Horizontal position
knob
7. Menu keys 8. Trigger level knob
9. Horizontal menu key 10. Trigger keys
11. TIME/DIV knob
12. EXT TRIG
13. Ground Terminal 14. CH2 Terminal
15. CH1/CH2 Math keys 16. CH1 Terminal
17. Probe Compensation
output
18. USB A type port
19. Power Switch
2. Turn to one of the three
preset positions.
3. Connect the power cord.
4. Press the power switch. The
display will become active
in approximately 10
seconds.
5. Reset the system by
recalling the factory
settings. Press the
Save/Recall key, then
Default Setup.
6. Connect the probe between the Channel1 input
terminal and probe compensation signal output
(2Vp-p, 1kHz square wave).
7. Set the probe attenuation voltage to x10.
This quick start guide contains proprietary information,
which is protected by copyright. All rights are reserved.
No part of this manual may be photocopied,
reproduced or translated to another language without
prior written consent of Good Will Corporation.
The information in this quick start guide was correct at
the time of printing. However, Good Will continues to
improve its products and therefore reserves the right to
change the specifications, equipment, and maintenance
procedures at any time without notice.
Good Will Instrument Co., Ltd. No. 7-1, Jhongsing Rd., Tucheng
Dist., New Taipei City 236, Taiwan.