System Sensor FAAST Comprehensive - Manual (Page 28)

parts and Accessories
ComprehenSive inSTruCTion mAnuAl
SCope
This section provides information on the parts and accessories available for
the FAAST system.
Note: Not all parts and accessories are available in all markets.
pArTS AnD ACCeSSorieS
Table 1 lists additional Parts and Accessories available for use with the
FAAST detector.
TABle 1. pArTS AnD ACCeSSorieS
TABle 2. pipe neTWorK pArTS AnD ACCeSSorieS
pArT no. iTem DeSCripTion
CMKT00100 FAAST Binder Provides key documents for
the FAAST system includ-
ing the Comprehensive
Instruction Manual .
I56-3620 Installation and
Maintenance Instructions
Describes the installation,
features and basic operation
of the FAAST detector .
F-A3384-000 Air Filter Disposable detector filter .
pipe neTWorK ComponenTS
TABLE 2 shows a list of the pipe fittings and accessories available for constructing
a pipe network for the FAAST detector.
pArT no. iTem imAGe DeSCripTion
P-PIPE-210 CPVC Pipe 15 ft . lengths, 3/4" Orange
CPVC pipe, 14 pieces, 210
ft . Total Length
P-ELB-90 90 degree
Elbow
90 degree CPVC Elbow,
3/4", Socket to Socket,
qty . 20
P-ELB-45 45 degree
Elbow
45 degree CPVC Elbow,
3/4", Socket to Socket,
qty . 10
P-TEE Tee 90 degree CPVC Tee, 3/4",
Socket to Socket, qty . 15
P-COUPLING Coupling CPVC Coupling, 3/4",
Socket to Socket, qty . 15
P-UNION Union CPVC Socket Union, 3/4",
qty . 10
P-ENDCAP End Cap CPVC End Cap, 3/4", qty .
25
P-LABEL-P Sampling
Point Labels
Sampling Point Labels, roll
of 100
P-LABEL-T Pipe Label Pipe Labels, roll of 100
P-SAMP-KT Sampling
Point Kit
Sampling Points with
Capillary Tubing, qty . 10
Note: Pipe and Fittings are listed to UL 1887.
lAnGuAGe CArDS
In addition to the standard English User Interface card, there are other lan-
guages available for use with the FAAST detector.
Table 3 lists the part numbers for ordering User Interface Cards and the lan-
guages that are available.
TABle 3. AvAilABle lAnGuAGeS For uSer inTerFACe CArD
pArT no. lAnGuAGe
F-LCARD-EN Language Card – English
F-LCARD-SP Language Card – Spanish
The User Interface Card can be easily replaced. To remove and replace the User
Interface card, follow the procedure outlined in Table 4.
TABle 4. uSer inTerFACe DiSplAY CArD replACemenT
STep proCeDure
1 Grasp the top of the card and gently lift the center of the card .
2 Carefully remove the card from the 6 mounting tabs, as shown in
FIGURE 1, from bottom to top .
3 When the card is removed from all of the tabs, remove the bottom
of the card from the pocket .
4 Install a new card by sliding the card into the pocket . Moving from
bottom to top, insert the card under each tab . If necessary, use a
flathead screwdriver to gently press the card in place beneath each
of the mounting tabs . The card is moderately flexible to allow for
some bending during installation .
FiGure 1. uSer inTerFACe CArD mounTinG
MOUNTING
TABS
MOUNTING
TABS
POCKET
ASP-65
SS-400-007 29 E56-3621-003
Parts and Accessories
FIR
E
DETECTION SYSTEM SAMPLIN
G
POIN
T
DO NOT
PA
IN T
FIR
E
DETECTION SYSTEM SAMPLIN
G
POIN
T
DO NOT
PA
IN
T
SMOKE DETECTOR SAMPLING TUBE
DO NOT DISTURB