Bell & Gossett S14367B Technologic Constant Speed Pump Controller - Manual (Page 37)

Technologic ® Constant Speed Pump Controller Installation, Operation and Maintenance Manual 37
Description Read Write Range/Value
Modbus Bacnet Lonworks N2
Address Address NV Index Address
System Start/Stop Status X 1=Start, 0=Stop 10001 BI 1 0 BI 1
System Auto/Manual Status X 1=Auto, 0=Manual 10002 BI 2 1 BI 2
General Alarm X 1=Fail, 0=OK 10003 BI 3 2 BI 3
Reset Required X 1=Reset is Required, 0=OK 10004 BI 4 3 BI 4
AI 1 Fail X 1=Fail, 0=OK 10005 BI 5 4 BI 5
AI 2 Fail X 1=Fail, 0=OK 10006 BI 6 5 BI 6
AI 3 Fail X 1=Fail, 0=OK 10007 BI 7 6 BI 7
AI 4 Fail X 1=Fail, 0=OK 10008 BI 8 7 BI 8
RTD 1 Fail X 1=Fail, 0=OK 10009 BI 9 8 BI 9
RTD 2 Fail X 1=Fail, 0=OK 10010 BI 10 9 BI 10
Battery Fail X 1=Fail, 0=OK 10011 BI 11 10 BI 11
Low Suction Pr (AI) X 1=Fail, 0=OK 10012 BI 12 11 BI 12
Low Suction Pr (Switch) X 1=Fail, 0=OK 10013 BI 13 12 BI 13
High Suction Pr X 1=Fail, 0=OK 10014 BI 14 13 BI 14
Low System Pr X 1=Fail, 0=OK 10015 BI 15 14 BI 15
High System Pr X 1=Fail, 0=OK 10016 BI 16 15 BI 16
NFSD (Diff. Temp) X 1=Fail, 0=OK 10017 BI 17 16 BI 17
NFSD (Flow Switch) X 1=Fail, 0=OK 10018 BI 18 17 BI 18
Low Level X 1=Fail, 0=OK 10019 BI 19 18 BI 19
High System Temperature X 1=Fail, 0=OK 10020 BI 20 19 BI 20
Pump1 DP Fail X 1=Fail, 0=OK 10021 BI 21 20 BI 21
Pump2 DP Fail X 1=Fail, 0=OK 10022 BI 22 21 BI 22
Pump3 DP Fail X 1=Fail, 0=OK 10023 BI 23 22 BI 23
Pump4 DP Fail X 1=Fail, 0=OK 10024 BI 24 23 BI 24
Pump5 DP Fail X 1=Fail, 0=OK 10025 BI 25 24 BI 25
Pump6 DP Fail X 1=Fail, 0=OK 10026 BI 26 25 BI 26
Pump1 OL Fail X 1=Fail, 0=OK 10027 BI 27 26 BI 27
Pump2 OL Fail X 1=Fail, 0=OK 10028 BI 28 27 BI 28
Pump3 OL Fail X 1=Fail, 0=OK 10029 BI 29 28 BI 29
Pump4 OL Fail X 1=Fail, 0=OK 10030 BI 30 29 BI 30
Pump5 OL Fail X 1=Fail, 0=OK 10031 BI 31 30 BI 31
Pump6 OL Fail X 1=Fail, 0=OK 10032 BI 32 31 BI 32
CAN fail X 1=Fail, 0=OK 10033 BI 33 32 BI 33
Voltage Tolerance Fail X 1=Fail, 0=OK 10034 BI 34 33 BI 34
Voltage Fail X 1=Fail, 0=OK 10035 BI 35 34 BI 35
System Start/Stop X 1=Start, 0=Stop 00001 BO 1 60 BO 1
System Reset X Positive Edge = Reset/Silence 00002 BO 2 61 BO 2
Pump Alternation X Positive Edge = Alternate 00003 BO 3 62 BO 3
Pump1 State X 0=Disabled, 1=Run, 2=Ready, 30001 AI 1 44 ADI 1
3=Failed
Section C — Serial Communications Points