Yamaha DIGITAL MIXING STUDIO 01X - Manual (Page 105)

01X Owner’s Manual
Remote Function List
105
Before Using
Basics Section
Appendix
Getting Started
Reference
[F8] ([SAVE] flashes)
This cancels the Save operation, when the final confirmation for Save appears ([SAVE]
flashes).
—
[SHIFT]+[F1]
Brings the Track View window to the front of the computer screen. (This operation
applies to the current song.)
—
[SHIFT]+[F2]
Displays the Mixer window (Audio Mixer/Multi Part Editor) or brings it to the front of
the computer screen.
—
[SHIFT]+[F3] Displays the List window or brings it to the front of the computer screen. —
[SHIFT]+[F4] Closes the current window. —
[SHIFT]+[F5] Displays the Piano Roll window or brings it to the front of the computer screen. —
[SHIFT]+[F6] No function —
[SHIFT]+[F7] Starts the TWE (Wave Editor). —
[SHIFT]+[F8] Alternately hides/shows the Transport window (Transport Bar/Location Bar/Record). —
[UNDO] Executes the Undo operation. —
[SHIFT]+[UNDO] Executes the Redo operation. —
[SAVE]
When the lamp lights, press this so that the lamp flashes. Press this again to execute the
Save operation (lamp turns off). Press [F8] to cancel it.
lights/flashes
[MARKER]+[WRITE] Enters/clears a Marker at the current song position. —
[r] Press briefly to move back one measure at a time, or hold to continuously rewind. —
[MARKER]+[r] Moves the song position to the previous Marker. —
[f]
Press briefly to move forward one measure at a time, or hold to continuously fast-for-
ward.
—
[MARKER]+[f] Moves the song position to the next Marker. —
[ ■]
Press to stop recording or playback. Pressing this when playback is stopped goes to the
top of the song.
—
[>] Press to start playback from the current point. lights
FOOT SWITCH 1 Playback/Stop —
[ ●] or FOOT SWITCH 2
Press this to enter/exit from the Recording Standby. The [>] (Play) and [ ●] (Rec) lamp
are turned on during recording.
lights
[ZOOM] Turns Zoom on and off. lights
Cursor [ ] ([ZOOM] goes out) Moves the cursor (indicating the current track) up. —
Cursor [ ] ([ZOOM] goes out) Moves the cursor (indicating the current track) down. —
Cursor [ ] ([ZOOM] goes out) Selects the previous block. —
Cursor [ ] ([ZOOM] goes out) Selects the next block. —
Cursor [ / / / ] ([ZOOM] lights) Zooms in/out in the active Track View and Piano Roll Window. —
Dial Moves the song position. (See “SCRUB” below.) —
[SCRUB]
Determines how the Scrub function is applied when using the dial. When this is set to on,
Scrub moves according to the Grid position in the Track View window. When set to off, it
moves in measures.
lights/goes out
PAN mode [PAN] lights
Knobs 1 – 8 (turning) Edits the Pan (on page 1). —
Knobs 1 – 8 (turning) Edits the Input level (on page 2). —
[SHIFT]+Knobs 1 – 8 (pressing) Resets the edited parameter to the default value (CENTER/0.00). —
AUX SEND mode [SEND] (Not available when the AUX/BUS window is active.) lights
Knobs 1 – 8 (turning) Edits the AUX Send Level. —
[SHIFT]+Knobs 1 – 8 (pressing) Resets the edited parameter to the default value (- ∞ ). —
EFF SEND mode [EFFECT] (Not available when the AUX/BUS window is active.) lights
Knobs 1 – 8 Edits the Effect Send Level. —
[SHIFT]+Knobs 1 – 8 Resets the edited parameter to the default value (- ∞ ). —
No function
[REC RDY] [LOOP] [EDIT] [FLIP]
Button Function LED
Notes
(page 114)