Tascam 2488neo - Manual (Page 108)

15 − Appendix
108
TASCAM 2488neo
Effect NRPN Parameter Values
Pitch Shifter (PIT)
00 00 Pitch 0 – 12 – 24 = –12 – 0 – +12
00 01 Fine 0 – 50 – 100 = –50 – 0 – +50
00 02 FB Delay 0 – 500 = 0 – 500 (msec)
00 03 Feedback 0 – 100 = 0 – 100
00 04 Level 0 – 127 = 0 – 127
Flanger (FLG)
00 00 Rate 1 – 100 = 0.1 – 10.0 (Hz)
00 01 Depth 0 – 100 = 0 – 100
00 02 FB Delay 0 – 1000 = 0 – 1000 (msec)
00 03 Feedback 0 – 100 = 0 – 100
00 04 Level 0 – 127 = 0 – 127
Phaser (PHA)
00 00 Rate 1 – 100 = 0.1 – 10.0 (Hz)
00 01 Depth 0 – 100 = 0 – 100
00 02 Resonance 0 – 100 = 0 – 100
00 03 Step 0 – 3 = 4, 8, 12, 16
00 04 Level 0 – 127 = 0 – 127
Gated reverb (GRV)
00 00 Type 0,1 = Normal, Reverse
00 01 Threshold 0 – 30 = –46 – –16 (dB)
00 02 Gate Time 1 – 300 = 10 – 3000 (msec)
00 03 Density 0 – 100 = 0 – 100
00 04 Level 0 – 127 = 0 – 127
Use MIDI channel 11 to set the parameters of this effect.
Note that this effect chains together a sequence of
effects (each step in the chain can hold one effect, the sequence in the chain of which is given in the first col-
umn of this table):
Multi effect
Effect
chain # Effect
NRPN Parameter Values
1
Noise suppressor
(NSP)
00 00 Threshold
0 – 100 = –84.0, –83.4, –82.8, –82.2, –81.6, –81.0, –80.4,
–79.8, –79.2, –78.6, –78.0, –77.4, –76.8, –76.2, –75.6, –75.0,
–74.4, –73.8, –73.2, –72.6, –72.0, –71.4, –70.8, –70.2, –69.6,
–69.0, –68.4, –67.8, –67.2, –66.6, –66.0, –65.4, –64.8, –64.2,
–63.6, –63.0, –62.4, –61.8, –61.2, –60.6, –60.0, –59.4, –58.8,
–58.2, –57.6, –57.0, –56.4, –55.8, –55.2, –54.6, –54.0, –53.4,
–52.8, –52.2, –51.6, –51.0, –50.4, –49.8, –49.2, –48.6, –48.0,
–47.4, –46.8, –46.2, –45.6, –45.0, –44.4, –43.8, –43.2, –42.6,
–42.0, –41.4, –40.8, –40.2, –39.6, –39.0, –38.4, –37.8, –37.2,
–36.6, –36.0, –35.4, –34.8, –34.2, –33.6, –33.0, –32.4, –31.8,
–31.2, –30.6, –30.0, –29.4, –28.8, –28.2, –27.6, –27.0, –26.4,
–25.8, –25.2, –24.6, –24.0 (dB)
00 01 Suppress 0 – 100 = 0 – 100
00 02 Attack 0 – 100 = 0 – 100
00 08 Release 0 – 100 = 0 – 100
00 04 Switch 0, 1 = Off, On