Tascam 2488neo - Manual (Page 104)

104
TASCAM 2488neo
The Bank Select controller is used with channel 15 to
choose which group of eight channels or inputs are affect-
ed. It is therefore necessary to send a MIDI message of BE
00 XX (where XX selects the group of eight channels or
inputs) before sending the Control Change messages on the
appropriate MIDI channel. Bank 0: Mixer channels 1 though 8
Bank 1: Mixer channels 9 through 16
Bank 2: Mixer channels 17 through 24
Bank 3: Inputs A through H
Once the group has been selected, use MIDI channels 1
through 8 to control the mixer channels or inputs or MIDI
channel 16 for the stereo master or send master).
Mixer Control Change parameters
MIDI channel
1–8 16
Mixer/Input channel STEREO/MASTER
Control Change
Number
Parameter Values
7 Internal Level 0 - 127 (0= –∞ dB, 100 = 0 dB, 127 = +6 dB)
10 Pan 1 = L63, 64 = Center, 127 = R63
—
11 Attenuation 0 – 8 = –42, –36, –30, –24, –18, –12, –6, 0, +6 (dB)
16 Low Freq
0 – 31 = 32, 40, 50, 60, 70, 80, 90, 100, 125, 150, 175, 200, 225, 250, 300, 350, 400,
450, 500, 600, 700, 800, 850, 900, 950, 1.0k, 1.1k, 1.2k, 1.3k, 1.4k, 1.5k, 1.6k (Hz)
17 Low Gain 0 – 24 = –12 to +12 (dB)
18 Mid Freq
0 – 63 = 32, 40, 50, 60, 70, 80, 90, 100, 125, 150, 175, 200, 225, 250, 300, 350, 400,
450, 500, 600, 700, 800, 850, 900, 950, 1.0k, 1.1k, 1.2k, 1.3k, 1.4k, 1.5k, 1.6k, 1.7k,
1.8k, 1.9k, 2.0k, 2.2k, 2.4k, 2.6k, 2.8k, 3.0k, 3.2k, 3.4k, 3.6k, 3.8k, 4.0k, 4.5k, 5.0k,
5.5k, 6.0k, 6.5k, 7.0k, 7.5k, 8.0k, 9.0k, 10k, 11k, 12k, 13k, 14k, 15k, 16k, 17k, 18k (Hz)
19 Mid Gain 0 – 24 = –12 to +12 (dB)
20 Mid Q 0 - 6 = 0.25, 0.5, 1, 2, 4, 8, 16
21 High Freq
32 – 63 = 1.7k, 1.8k, 1.9k, 2.0k, 2.2k, 2.4k, 2.6k, 2.8k, 3.0k, 3.2k, 3.4k, 3.6k, 3.8k,
4.0k, 4.5k, 5.0k, 5.5k, 6.0k, 6.5k, 7.0k, 7.5k, 8.0k, 9.0k, 10k, 11k, 12k, 13k, 14k, 15k,
16k, 17k, 18k (Hz)
22 High Gain 0 – 24 = –12 to +12 (dB)
23 LOOP Effect Level 0 – 127 (0= –∞ dB, 100 = 0 dB, 127 = +6 dB) (MASTER LEVEL)
24 EFFECT1 Level 0 – 127 (0= –∞ dB, 100 = 0 dB, 127 = +6 dB) (MASTER LEVEL)
25 EFFECT2 Level 0 – 127 (0= –∞ dB, 100 = 0 dB, 127 = +6 dB) (MASTER LEVEL)
80 EQ SW 0, 1 = OFF, ON
81 LOOP Effect Pos 0, 1 ,2 = OFF, PRE, POST
—
82 EFFECT1 Pos 0, 1, 2 = OFF, PRE, POST
83 EFFECT2 Pos 0, 1, 2 = OFF, PRE, POST
84 Phase 0, 1 = N, R
The following are the MIDI Control Change messages
accepted by the 2488neo to control different settings.
When used with an external sequencer, this provides a cer-
tain degree of automation for mixing, etc.
MIDI Control/Program change message
15 − Appendix