Extron Electronics MLC 104 Plus Series - Manual (Page 83)

4-19 MLC 104 Plus Series • SIS Programming and Control
PRELIMINAR
Y
Command/r
esponse table for SIS commands (continued
)
Command
ASCII (T
elnet
)
(host to MLC
)
URL Encoded (W
eb
)
(host to MLC
)
Response (MLC to host
)
Additional description Show the absence of or types of connected devices.
Prefixes for connected devices: P1 =
SCP
#1, addr
ess 0
P2 =
SCP
#2, addr
ess 1
K1 =
contr
ol module #1, addr
ess 0
K2 =
contr
ol module #2, addr
ess 1
K3 =
contr
ol module #3, addr
ess 2
K4 =
contr
ol module #4, addr
ess 3
S =
MediaLink device, typically a slaved (auxiliary) MLS switcher
.
For : 00 = not pr
esent
01 = MLS 306 02 = MLS 506 03 = MLS 506MA
70 V
04 = MLS 506SA 05 = MLS 506MA
100 V
06 = MLS 100
A
07 = MLS 103 V 08 = MLS 103 SV
09 = MLS 102 VGA 10 = MLA-VC10 11
= MLS 304MA
12 = MLS 406 13 = MLS 406MA 14 = MLS 406SA 15 = MLS 304SA 16 = PVS 204SA 99 = non-MLS, non-
PVS switcher
.
For ##: 00 = not pr
esent
01 = pr
esent (SCP)
or
IRCM-VCR
02 = IRCM-DVD 03 = IRCM DVD+ 04 =
ACM-Level
05 =
ACM-T
one
06 = RCM-SC 07 = RCM-SC
LT
08 = IRCM-T
ape
09 = CM-5BB 10 = CM-20BB 11
= IRCM-DV+
12 = CM-9BLB 13 = CM-3BLB 14 = CM-19AC 99 = unr
ecognized.
000 = not pr
esent
101 = IPI 101
AAP
104 = IPI 104
AAP
For ???:
Examples:
32I
32I
P101 P200 K1
11 K21
1 K307 K408 S09
]
This example includes one SCP
(P101),
an IRCM
-DVD+ (K1
11 and K21
1), an
RCM
-SCL
T (K307), an IRCM
-T
ape (K408),
and an MLS 102 VGA
(S09).
IP setup commands (IP models only
)
Set the unit name
24
E
X1@
C
N
}
W
X1@
CN
|
Ipn•
X1@
]
Change the MLC’s name to one of your choosing (
X1@
), such as “AuditoriumMLC”,
“Rm316-A
Vcenter”, or “exec-boar
dr
oom-
ctrl”. The name consists of up to 24 alphanumeric characters (and the minus sign). The first character must be a letter
,
the last character cannot be a minus sign (hyphen). Either case (upper
, lower) is OK.
Set unit name to factory default
24
E
•CN
}
W%20CN
|
Ipn•
X4(
]
X4(
= the name the MLC was shipped with:
MLC-104-IP-PLUS
-##
-##
-##, a combination
of the model name and the last 3 pairs of hex numbers in the contr
oller
’s MAC
addr
ess (e.g., MLC-104-IP-PLUS-02-74-62).
Read the unit name
E
CN
}
WCN
|
X1@
]
or
X4(
]
X1@
is the MLC’s curr
ent, user
-defined unit
name. X4(
is the MLC’s factory default name.
N
The non
‑IP model accepts these commands, but it does not have a LAN port, so it cannot make use of the settings.