Skutch Electronics BA-1000-A Technical Reference Guide - Manual (Page 22)

Version 6.XX Page 22
Enter from
02 02 02 02
to
32 32 32 32
then press then release
# # # #
to go to the next option. You can press then release
~ ~ ~ ~
to return to the Total Calls screen.
TT Off Time= 02
This option sets how long the system waits between each
touch tone dialed. Some paging systems require longer delays
before dialing the next touch tone, to allow the automated
message system to catch up with the touch tones being entered;
this allows you to increase that time. For this option, 1 = 1
second. The display will look as follows:
TT Off Time= 02
02 to 32 #=Next
Enter from
02 02 02 02
to
32 32 32 32
then press then release # to
go to the next option. You can press then release
~ ~ ~ ~
to return to the Total Calls screen.
Vbox Mode= off
This option lets you turn Voice Mail box mode on/off.
The display looks as follows:
Vbox Mode= off
1=Change #=Next
Press then release
1 1 1 1
to toggle between On and Off;
press then release
# # # #
to go to the next option. You can press
then release
~ ~ ~ ~
to return to the Total Calls screen.
Vbox PINs
These next 16 entries are the PINs used to access the
different Voice Mail boxes. The display will look as follows:
Vbox 01 PIN>0101
1=Change #=Next
You can press then release
1 1 1 1
to change the PIN,
followed by the
# # # #
, or press then release
# # # #
to proceed to the
next option. To exit from this mode, press then release
~ ~ ~ ~
to return to Total Calls .
Multi-type= off
This option lets you turn Multi-type on/off. Multi-type
allows you to give a different ending to each message file you
record. An example is: you record one message to just get the
caller’s information, and another message to alert on a Touch
Tone
8 8 8 8
.
If Multi-type is turned ON, then, after you release the
5 5 5 5
,
while recording your messages, the system will scroll between
several options as follows:
1=Play Only
The message will play, but not record anything from the
caller.
2=Record Only
The message will play, then record from the caller, but it
will not trigger.
3=Play and Voice trigger
The message will play, then record from the caller, then it
will Alert if it did record some audio.
4=Play and Tone trigger
The message will play, then record from the caller, then it
will Alert if it did record some audio and the call dials a Touch
Tone
8 8 8 8
after their message.
The display looks as follows:
Multi-type= off
1=Change #=Next
Press then release
1 1 1 1
to toggle between On and Off;
press then release
# # # #
to go to the next option. You can press
then release
~ ~ ~ ~
to return to the Total Calls screen.
Ignore TT#= off
This option tells the system whether it should ignore
looking for the
# # # #
Touch Tone when it is playing messages.
This is used mostly for trouble shooting by out techs. The
display looks as follows:
Ignore TT#= off
1=Change #=Next
Press then release
1 1 1 1
to toggle between On and Off;
press then release
# # # #
to go to the next option. You can press
then release
~ ~ ~ ~
to return to the Total Calls screen.
Remote Erase= on
This option tells the system whether it should allow
messages to be erased remotely (on) or silently save the
messages when someone tries to erase them remotely (off). The
display looks as follows:
Remote Erase= on
1=Change #=Next
Press then release
1 1 1 1
to toggle between On and Off;
press then release
# # # #
to go to the next option. You can press
then release
~ ~ ~ ~
to return to the Total Calls screen.
* * *
Trouble shooting
This section has been provided to help the user in case of
problems. For best results, all of the following procedures
should be read and followed. If after the following steps, you
are still having problems, go to the Customer Support section.