Installation, Location, Power – Skutch Electronics BA-1000-A Technical Reference Guide User Manual
Page 6: 4 selectable urgent call modes, Voice confirmation, Dialing sequence reset, Voice mail box mode, Remote control features, Power fail friendly, Other features

Version 6.XX
Page 6
4 Selectable Urgent Call Modes
Selectable URGENT CALL MODES allow immediate
notification of ONLY your calls that need immediate attention.
The BA-1000-A can call you on your home phone, your cell
phone or even on your pager. The BA-1000-A is persistent. It
knows that you need to be notified and it keeps working until the
message is retrieved. The unit has adjustable
redials
and
adjustable
time between calls
.
Voice Confirmation
When the BA-1000-A has detected an urgent call, it will
confirm the URGENT CALL, to the calling party, by saying:
"You'll be called as soon as possible. Please hang up now".
Dialing Sequence Reset
The BA-1000-A can be set up to keep calling you until the
URGENT MESSAGE has been received. When the BA-1000-A
calls you at home or on your cell phone, it will wait until the
phone is answered, then it will play the following message: "I
have an URGENT message from your office. Enter the
ACCESS CODE." When the access code is entered, the
message will be played back and the dialing sequence will be
reset.
If the BA-1000-A is calling your pager, it will notify you
by displaying a pre-programmed, user selectable number. In
this case the user must call the BA-1000-A and, during the
announcement, enter the access code. The URGENT message
will be played back, once the
access code
is entered, and the
dialing sequence is reset.
Voice Mail box mode
This mode allows the BA-1000-A to function as a true
Voice Mail Box system. In this mode you can have from 1 to 16
boxes with up to 8 urgent numbers per box.
Remote Control Features
Verbal Message Counter.
Automatic Message Playback with verbal Date
and Time Stamp.
User controllable functions: Message Skip,
Repeat, Save, Erase, and auto Pause between
messages.
Programmable 4 digit
access code
(Changeable
Locally Only).
Remote Outgoing Message recording and
playback
.
Remote Notification Number programming,
enabling or disabling
.
Remote
START GROUP
programming.
Power Fail Friendly
If the power fails, the BA-1000-A will remember its exact
mode. So, when power is restored, the BA-1000-A will resume
where it left off; whether dialing or waiting for calls to come in.
Other Features
Programmable
Ring Delay
from 1 to 12, or Toll
Saver mode.
Announce ONLY Mode
.
Voice Controlled
Recording.
Maximum Record Time Limit
, adjustable from
10 seconds to 4 minutes, or unlimited.
CPC Disconnect
(ON/OFF).
Dial Tone disconnect
(ON/OFF)
Auto Disconnect on Local Pick Up, the unit
automatically disconnects when you pick up a
local phone.
Disk FULL message. A special message plays
when the BA-1000-A runs out of message storage
space: "System full please try again later".
Four
digit
user
programmable
remote
programming
access code
.
Automatic clock control
can be set to let the unit
turn itself on during non-business hours.
128, 32 digit, notification phone numbers can be
user programmed.
Installation
Location
When selecting a location for the system, the following
conditions MUST be avoided:
Temperatures above 95°F.
Temperatures below 65°F.
Carpeted areas that produce Static Electricity.
High dust/tobacco smoke areas.
Exposure to direct sunlight.
The SYSTEM and the POWER CUBE should be located
in a well ventilated area. It should be noted that the POWER
CUBE can get quite warm during operation. Make sure that
both a three-prong power outlet and a proper telephone jack are
within six feet of the installation site.
Power
The SYSTEM can be used on a three-prong grounded
110VAC power outlet. This is needed for proper protection of
the unit’s circuitry. Power circuits that are used for any heavy
equipment such as large freezers, blowers, heaters, copiers, or
any electrical equipment that contains large motors, should be
avoided. Heavy electrical equipment can cause power glitches
over the power line which could interfere with the operation of
the system. If your power lines are excessively noisy a power
filter MIGHT solve the problem.