Hidden setup options, Start group= 1, Total calls – Skutch Electronics BA-1000-A Technical Reference Guide User Manual
Page 19: Set auto clock, Select the day to change, Set the start time, Set the stop time

Version 6.XX
Page 19
Enter from
00
00
00
00
to
99
99
99
99
then press then release # to
go to the next option. You can press then release
~
~
~
~
to exit setup mode.
Start Group= 1
This parameter is used in ALERT MODES
2
and
3
. In
either of these modes, if the caller dials
8
8
8
8
, then the group,
defined by this parameter, will Alert dialed.
The following shows the Notification Entries that are used
for each Tone Response.
Start Group
Notification Entries
1
1-8
2
9-16
3
17-24
4
25-32
5
33-40
6
41-48
7
49-56
8
57-64
9
65-72
10
73-80
11
81-88
12
89-96
13
97-104
14
105-112
15
113-120
16
121-128
This parameter can also be changed in remote mode. The
display will look as follows:
Start Group= 01
1 to 16 #=Next
Press then release
1
1
1
1
for group 1,
2
2
2
2
for group 2, etc.,
or press then release
#
#
#
#
to proceed to the next option. You can
press then release
~
~
~
~
to exit setup mode.
Total Calls
This is a inbound call counter. It shows the grand total
number of inbound messages left on the system. This count is
not resettable. The display will look as follows:
- Total Calls -
----00000000----
You can press then release
#
#
#
#
or
~
~
~
~
to
return to IDLE. You can access the hidden setup, while it
shows the Total Calls, by entering:
* * * * #
* * * * #
* * * * #
* * * * #
* * *
Hidden Setup Options
The hidden setup contains settings that should only be
changed by experienced users. It is entered, from the
Total
Calls
window, in Setup Mode, by entering:
* * * * #
* * * * #
* * * * #
* * * * #
Set AUTO CLOCK
This option allows you to set the starting and stopping
times, for each day of the week, that the system uses to
enter/exit clock controlled auto answer mode; the display will
look as follows:
Set AUTO CLOCK
1=Change #=Next
You can press then release
1
1
1
1
to change the times or
#
#
#
#
to proceed to the next option. You can press then release
~
~
~
~
to return to
Total Calls
. The default times are to
start at 5:00 p.m. and end at 8:00 a.m.
• Select The Day To Change
Press then release
1
1
1
1
to change the time; the display
shows:
Enter day, 1 – 7
#=Sunday
To change the auto times for a day, press then release the
corresponding number followed
#
#
#
#
; example, enter
1
1
1
1
for
Sunday,
2
2
2
2
for Monday, etc.
• Set The Start Time
This is the time you want the system to activate itself
(normally this is your quitting time). Now the display will
show:
Answering START
- # = 05:00 pm –
Now you can enter a new start time followed by
#
#
#
#
, or
just press then release
#
#
#
#
to keep the current time. You can
change between a.m./p.m. by pressing then releasing the
*
*
*
*
.
• Set The Stop Time
This is the time you want the system to return to Idle
Mode (normally this is the time you start work). Now the
display will show:
Answering STOP
- # = 08:00 am –
Now you can enter a new stop time followed by
#
#
#
#
, or
just press then release
#
#
#
#
to keep the current time. You can
change between a.m./p.m. by pressing then releasing the
*
*
*
*
.