Programmable remote (pr) v/c module -7, Timer/counter -7 – Hypertherm HT4001 Plasma Arc Cutting System User Manual
Page 98
OPERATION
HT4001
Instruction Manual
5-7
Programmable Remote (PR) V/C Module (Fig. 5-5)
• VOLTAGE LEDs
Displays cutting voltage during cut sequence.
• CURRENT LEDs
Displays cutting current during cut sequence.
• UP / DOWN LEDs
Indicates that torch height is being adjusted up or down.
Timer/Counter (Fig. 5-6)
Each LCD counter is self-powered by a three-volt lithium battery.
• STARTS LCD Counter (w/Reset)
Indicates the number of arc starts.
• ARC TIME LCD Counter
Indicates the cumulative time that the arc is on in hours.
• ERRORS LCD Counter (w/Reset)
Indicates the number of times that the arc cut cycle ends before the programmed current ramp down time
has elapsed. This reading provides a direct correlation to the long-life operation of the electrode; the higher
the reading, the shorter the electrode life.
Figure 5-5
Programmable Remote (PR) V/C Front Panel Indicators
Figure 5-6
Timer / Counter Front Panel Indicators
Reset
Reset
- EDGE Pro Ti Shape Cutting Control Rev.2 (288 pages)
- 80669J Rev.3 (304 pages)
- HD3070 Plasma Arc Cutting System w/ Manual Gas Console (281 pages)
- MAXPRO200 Rev.2 (294 pages)
- MicroEDGE Pro Shape Cutting Control Rev.2 (182 pages)
- Powermax1650 (317 pages)
- HPR260 Auto Gas Preventive Maintenance Program Rev.4 (288 pages)
- Shape Cutting Control (66 pages)
- PHC Sensor (58 pages)
- HTA Rev 6.00 Operators Manual (212 pages)
- HTA Rev 7.00 Install Guide (242 pages)
- THC Control Board Replacement (13 pages)
- THC Plasma Interfacer Upgrade (9 pages)
- THC X-Y Table Product Configuration (20 pages)
- D845GERG2 (128 pages)
- MRT2 (64 pages)
- MRT (98 pages)
- Duramax Hyamp Long Handheld Torches (92 pages)
- Duramax Hyamp Robotic Torch (74 pages)
- HyIntensity Fiber Laser Rev.3 (240 pages)
- PCBS-0124 (70 pages)
- SuperMicro 370SBA 533Mhz (90 pages)
- LR2075 (56 pages)
- Phoenix 8.0 (585 pages)
- LH2125 (60 pages)
- HD3070 w/ Automatic Gas (35 pages)
- HD3070 w/Manual Gas (43 pages)
- HD4070 Rev.8 (278 pages)
- HD4070 Product Configuration (88 pages)
- HPR800XD Manual Gas Preventive Maintenance Program Rev.1 (32 pages)
- HPR800XD Manual Gas Preventive Maintenance Program Rev.1 (33 pages)
- HPR800XD Manual Gas Rev.2 (368 pages)
- HPRXD Short Torch with Integrated Lead Rev.1 (30 pages)
- HT4001 (59 pages)
- DuraChill 5 HP Air-Cooled Chiller For Hypertherm (29 pages)
- HT4001 Air Injected Water Muffler System (40 pages)
- H601 Power Supplies (62 pages)
- MAX200 Remote Switch (9 pages)
- HT4100 Plasma Arc Cutting System Operating (50 pages)
- HSD130 HySpeed Plasma (233 pages)
- HySpeed HT2000 Plasma Arc Cutting System Rev.7 (53 pages)
- HySpeed HT2000 Plasma Arc Cutting System Rev.27 (289 pages)
- MAX200 Water Muffler (39 pages)
- HT2000LHF Product Configuration (23 pages)