H401 slave modification – Hypertherm HT4001 Plasma Arc Cutting System User Manual
Page 224
APPENDIX A
4-00
a-2
HT4001
Instruction Manual
H401 Slave Modification
A PC board assembly must be added to the stock H401 power supply so that it can interface as a slave for the
HT4001 system. Kit 128315 contains the necessary components to make this change:
Part No.
Description
Qty.
128315
Kit:H401/601 Slave
008340
Standoff:8-32 X 1/4 Hex X 1" Lg Al
4
075022
M/S:8-32 X 3/8 PH PAN SST
4
041366
PCB Assy:HT4001 Cur Set Pt
1
023136
Cable:4/0 1/2Lug 20'
2
123377
Cable:HT4001 Slave 25'
1
129375
Harness: Kit 128315
1
802930
FSB: Slave Calibration
1
Adding the Current Setpoint PCB to the H401 Slave – Fig. a-1
1. Remove both side panels and top panel to the H401 power supply.
2. Find the center wall of the H401 supply that supports the terminal strip.
3. Attach the Current Setpoint PCB to the center wall.
WARNING
Make all H401 power supply modifications before hooking up power cord.
- EDGE Pro Ti Shape Cutting Control Rev.2 (288 pages)
- 80669J Rev.3 (304 pages)
- HD3070 Plasma Arc Cutting System w/ Manual Gas Console (281 pages)
- MAXPRO200 Rev.2 (294 pages)
- MicroEDGE Pro Shape Cutting Control Rev.2 (182 pages)
- Powermax1650 (317 pages)
- HPR260 Auto Gas Preventive Maintenance Program Rev.4 (288 pages)
- Shape Cutting Control (66 pages)
- PHC Sensor (58 pages)
- HTA Rev 6.00 Operators Manual (212 pages)
- HTA Rev 7.00 Install Guide (242 pages)
- THC Control Board Replacement (13 pages)
- THC Plasma Interfacer Upgrade (9 pages)
- THC X-Y Table Product Configuration (20 pages)
- D845GERG2 (128 pages)
- MRT2 (64 pages)
- MRT (98 pages)
- Duramax Hyamp Long Handheld Torches (92 pages)
- Duramax Hyamp Robotic Torch (74 pages)
- HyIntensity Fiber Laser Rev.3 (240 pages)
- PCBS-0124 (70 pages)
- SuperMicro 370SBA 533Mhz (90 pages)
- LR2075 (56 pages)
- Phoenix 8.0 (585 pages)
- LH2125 (60 pages)
- HD3070 w/ Automatic Gas (35 pages)
- HD3070 w/Manual Gas (43 pages)
- HD4070 Rev.8 (278 pages)
- HD4070 Product Configuration (88 pages)
- HPR800XD Manual Gas Preventive Maintenance Program Rev.1 (32 pages)
- HPR800XD Manual Gas Preventive Maintenance Program Rev.1 (33 pages)
- HPR800XD Manual Gas Rev.2 (368 pages)
- HPRXD Short Torch with Integrated Lead Rev.1 (30 pages)
- HT4001 (59 pages)
- DuraChill 5 HP Air-Cooled Chiller For Hypertherm (29 pages)
- HT4001 Air Injected Water Muffler System (40 pages)
- H601 Power Supplies (62 pages)
- MAX200 Remote Switch (9 pages)
- HT4100 Plasma Arc Cutting System Operating (50 pages)
- HSD130 HySpeed Plasma (233 pages)
- HySpeed HT2000 Plasma Arc Cutting System Rev.7 (53 pages)
- HySpeed HT2000 Plasma Arc Cutting System Rev.27 (289 pages)
- MAX200 Water Muffler (39 pages)
- HT2000LHF Product Configuration (23 pages)