H401 slave connections (cont.) – Hypertherm HT4001 Plasma Arc Cutting System User Manual
Page 232
APPENDIX A
a-10
HT4001
Instruction Manual
H401 Slave Connections (cont.)
When using the H401 Slave, a positive and negative lead must connect the HT4001 to the H401. Two 25-foot
cables (023136) come with the 077011 kit for this purpose.
Also, an additional positive lead must run from the positive bus bar in the HT4001 power supply to the work table,
and an additional negative lead must run from the negative bus bar in the HT4001 power supply to the cathode
block of the RHF console.
Refer to Fig. a-6.
Positive Lead – HT4001 Power Supply to H401 Power Supply
Negative Lead – HT4001 Power Supply to H401 Power Supply
Positive Lead – HT4001 Power Supply to Work Table
Negative Lead – HT4001 Power Supply to RHF Console
31
32
33
34
Part No.
Length
023136
20 ft (6 m)
023078
25 ft (7.5 m)
023101
30 ft (9 m)
023135
40 ft (12 m)
023079
50 ft (15 m)
Part No.
Length
023124
75 ft (23 m)
023080
100 ft (30.5 m)
023081
150 ft (46 m)
023316
180 ft (55 m)
023188
200 ft (61 m)
- EDGE Pro Ti Shape Cutting Control Rev.2 (288 pages)
- 80669J Rev.3 (304 pages)
- HD3070 Plasma Arc Cutting System w/ Manual Gas Console (281 pages)
- MAXPRO200 Rev.2 (294 pages)
- MicroEDGE Pro Shape Cutting Control Rev.2 (182 pages)
- HPR260 Auto Gas Preventive Maintenance Program Rev.4 (288 pages)
- Powermax1650 (317 pages)
- Shape Cutting Control (66 pages)
- PHC Sensor (58 pages)
- HTA Rev 6.00 Operators Manual (212 pages)
- HTA Rev 7.00 Install Guide (242 pages)
- THC Control Board Replacement (13 pages)
- THC Plasma Interfacer Upgrade (9 pages)
- THC X-Y Table Product Configuration (20 pages)
- D845GERG2 (128 pages)
- MRT2 (64 pages)
- MRT (98 pages)
- Duramax Hyamp Long Handheld Torches (92 pages)
- Duramax Hyamp Robotic Torch (74 pages)
- HyIntensity Fiber Laser Rev.3 (240 pages)
- PCBS-0124 (70 pages)
- SuperMicro 370SBA 533Mhz (90 pages)
- LR2075 (56 pages)
- Phoenix 8.0 (585 pages)
- LH2125 (60 pages)
- HD3070 w/ Automatic Gas (35 pages)
- HD3070 w/Manual Gas (43 pages)
- HD4070 Rev.8 (278 pages)
- HD4070 Product Configuration (88 pages)
- HPR800XD Manual Gas Preventive Maintenance Program Rev.1 (32 pages)
- HPR800XD Manual Gas Preventive Maintenance Program Rev.1 (33 pages)
- HPR800XD Manual Gas Rev.2 (368 pages)
- HPRXD Short Torch with Integrated Lead Rev.1 (30 pages)
- HT4001 (59 pages)
- DuraChill 5 HP Air-Cooled Chiller For Hypertherm (29 pages)
- HT4001 Air Injected Water Muffler System (40 pages)
- H601 Power Supplies (62 pages)
- MAX200 Remote Switch (9 pages)
- HT4100 Plasma Arc Cutting System Operating (50 pages)
- HSD130 HySpeed Plasma (233 pages)
- HySpeed HT2000 Plasma Arc Cutting System Rev.7 (53 pages)
- HySpeed HT2000 Plasma Arc Cutting System Rev.27 (289 pages)
- MAX200 Water Muffler (39 pages)
- HT2000LHF Product Configuration (23 pages)