Nitrogen, Ht4001 with slave, Pac620 torch – beveling consumables – Hypertherm HT4001 Plasma Arc Cutting System User Manual
Page 122: Mild steel or stainless steel – nitrogen plasma

11-96
HT4001
Instruction Manual
5-31
HT4001 with Slave
PAC620 Torch – Beveling Consumables
Mild Steel or Stainless Steel – Nitrogen Plasma
Retaining Cap
120390 (Vect)
120391 (Vesp)
Nozzle
120386
(.120 in/3 mm)
120389
(.220 in/5.5 mm)
Swirl Ring
020039 (cw)
020042 (ccw)
020040 (cw)
020079 (ccw)
Electrode
020968
Water Tube – N
2
Bevel
020991
120387
(.166 in/4.2 mm)
120388
(.187 in/4.7 mm)
Notes:
• Minimum N
2
inlet supply pressure remains at one setting of 150 psi (10.3 bar) for all material thickness.
• Water chiller pump outlet pressure remains between 175-185 psi (12-12.8 bar) for all material thickness.
• N
2
flow rate at full scale is 374 scfh (176 l/min) @ 150 psi (10.3 bar) inlet pressure.
• Set initial torch height (before piercing) to approximately twice the Torch Standoff distance for the material you are cutting.
Note: If arc does not transfer when set at twice the torch standoff (in the case of thick metal being cut at high current). gradually
lower the initial height of the torch until transfer occurs.
120470 – CE (Vect)
120471 – CE (Vesp)
E
N
G
L
I
S
H
M
E
T
R
I
C
Test Preflow
Rate
Test Cut Flow
Rate
(N
2
)
(N
2
)
(in)
(mm)
(%)
(%)
(%)
(in)
(mm)
(ipm)
(mm/min)
.035
.889
30
30
45
125
240
1/8
3
425
10800
.075
1.91
30
30
45
130
240
1/8
3
285
7240
1/8
3.18
30
30
45
145
240
3/16
5
190
4820
1/4
6.35
30
30
45
155
240
3/16
6
145
3680
1/8
3.18
45
45
62
125
300
1/4
6
170
4320
1/4
6.35
45
45
62
135
340
1/4
6
140
3550
3/8
9.53
45
45
62
145
360
1/4
6
120
3050
1/2
12.7
45
45
62
145
380
5/16
7
90
2280
3/4
19.1
45
45
62
150
400
5/16
7
50
1270
1
25.4
45
45
62
155
400
3/8
10
30
760
1/2
12.7
55
55
65
140
480
3/8
10
100
2540
3/4
19.1
55
55
65
145
500
3/8
10
70
1780
1
25.4
55
55
65
150
560
3/8
10
60
1520
1-1/2
38.1
55
55
65
165
580
3/8
10
30
760
2
50.8
55
55
65
175
600
7/16
10
20
510
1-1/4
31.8
60
60
73
170
700
1/2
13
40
1020
2
50.8
60
60
73
175
720
1/2
13
25
630
3
76.2
60
60
73
185
760
5/8
16
12
300
.166"
400A max.
.187"
600A max.
.220"
760A max.
Arc
Current
(A)
Torch
Standoff
Travel Speed
.120"
260A max.
Nozzle
Material
Thickness
Water Flow
Setting
Arc Volts
(V)
Test Preflow
Rate
Test Cut Flow
Rate
(N
2
)
(N
2
)
(mm)
(%)
(%)
(%)
(mm)
(mm/min)
3 mm
260A max.
6
30
30
45
155
240
5
3800
6
45
45
62
135
340
6
3640
8
45
45
62
140
360
6
3300
10
45
45
62
145
360
6
2930
12
45
45
62
145
380
6-7
2450
15
45
45
62
150
400
8
1910
20
45
45
62
150
400
8
1190
25
45
45
62
155
400
10
790
15
55
55
65
140
500
10
2260
20
55
55
65
145
500
10
1740
25
55
55
65
150
560
10
1540
35
55
55
65
160
580
10
950
50
55
55
65
175
600
11
530
35
60
60
73
170
700
13
950
50
60
60
73
175
720
13
650
60
60
60
73
180
740
15
510
75
60
60
73
185
760
16
320
4.7 mm
600A max.
5.5 mm
760A max.
Arc
Current
(A)
Torch Standoff
Travel Speed
4.2 mm
400A max.
Nozzle
Material
Thickness
Water Flow
Setting
Arc Volts
(V)