System units placement -4, System units placement, Installation – Hypertherm HT4001 Plasma Arc Cutting System User Manual
Page 57: Ht4001
INSTALLATION
11-97
4-4
HT4001
Instruction Manual
System Units Placement
• Position all required units prior to making electrical, gas, and interface connections.
• See Section 2 for mounting dimensions of all units.
• Ground all external modules in the HT4001 system to earth.
• To prevent leaks in the system, tighten all gas and water connections to the following specifications:
* System shown includes H401 slave, IHS, and water muffler options
Air
Air
Torch
Machine
Interface
Motor
Valve
Console
Water
Muffler
IHS
Probe
Air
Regulator
Gas Console (mount near operator)
RHF Console
IHS Console
Timer/Counter
Water
Chiller
HT4001
Remote V/C Control
(mount near operator)
Water
Power
H401
Slave
(optional)
Water Muffler
Pump
Power
Power
Figure 4-2
Typical HT4001 System* Component Placement for Gantry Cutter
Gas or water
Torch Specification
hose size
lbf-in
lbf-ft
kgf-cm
Up to 3/8" (9.5 mm)
75-85
6.25-7
86-98
1/2" (12.7 mm)
360-480
30-40
415-550
- EDGE Pro Ti Shape Cutting Control Rev.2 (288 pages)
- 80669J Rev.3 (304 pages)
- HD3070 Plasma Arc Cutting System w/ Manual Gas Console (281 pages)
- MAXPRO200 Rev.2 (294 pages)
- MicroEDGE Pro Shape Cutting Control Rev.2 (182 pages)
- HPR260 Auto Gas Preventive Maintenance Program Rev.4 (288 pages)
- Powermax1650 (317 pages)
- Shape Cutting Control (66 pages)
- PHC Sensor (58 pages)
- HTA Rev 6.00 Operators Manual (212 pages)
- HTA Rev 7.00 Install Guide (242 pages)
- THC Control Board Replacement (13 pages)
- THC Plasma Interfacer Upgrade (9 pages)
- THC X-Y Table Product Configuration (20 pages)
- D845GERG2 (128 pages)
- MRT2 (64 pages)
- MRT (98 pages)
- Duramax Hyamp Long Handheld Torches (92 pages)
- Duramax Hyamp Robotic Torch (74 pages)
- HyIntensity Fiber Laser Rev.3 (240 pages)
- PCBS-0124 (70 pages)
- SuperMicro 370SBA 533Mhz (90 pages)
- LR2075 (56 pages)
- Phoenix 8.0 (585 pages)
- LH2125 (60 pages)
- HD3070 w/ Automatic Gas (35 pages)
- HD3070 w/Manual Gas (43 pages)
- HD4070 Rev.8 (278 pages)
- HD4070 Product Configuration (88 pages)
- HPR800XD Manual Gas Preventive Maintenance Program Rev.1 (33 pages)
- HPR800XD Manual Gas Preventive Maintenance Program Rev.1 (32 pages)
- HPR800XD Manual Gas Rev.2 (368 pages)
- HPRXD Short Torch with Integrated Lead Rev.1 (30 pages)
- HT4001 (59 pages)
- DuraChill 5 HP Air-Cooled Chiller For Hypertherm (29 pages)
- HT4001 Air Injected Water Muffler System (40 pages)
- H601 Power Supplies (62 pages)
- MAX200 Remote Switch (9 pages)
- HT4100 Plasma Arc Cutting System Operating (50 pages)
- HSD130 HySpeed Plasma (233 pages)
- HySpeed HT2000 Plasma Arc Cutting System Rev.7 (53 pages)
- HySpeed HT2000 Plasma Arc Cutting System Rev.27 (289 pages)
- MAX200 Water Muffler (39 pages)
- HT2000LHF Product Configuration (23 pages)