Interlogix XL LCD Keypad Plus Regional Settings Guide - Manual (Page 84)

80 xL Regional Settings Guide 21-3609E rev1.0
52 Any area Failed to Close
53 Phone Line Failure
54 Local AC (mains) failure.
55 System Tamper – European Version .
56 System Fault – European Version.
57 System WAS IN ALARM. This is only for
input points in alarm e.g. NOT for
system trouble (clears when alarmed
areas are turned off)
57 Strobe (Netherlands, Australia/NZ
Regional Setting)
58 Bypass is in effect in any armed area.
European Version (System)
59 Fire
60 Personal
Attack
61 Unconfirmed Alarm
62 Area Set / Unset
63 Freezer / Fire Fault
64 Bypass in Effect
65 Confirmed Alarm
66 Siren
67
Confirmed Alarm (Strobe)
System Special Outputs. Section Range: 001 – 001. See
examples 8 & 9 in Output Examples. NOTE: Only
configurable through the Director Software.
00 1 sec on, 1 sec off
01 2 seconds on every minute
02 10 seconds on every minute
Program Section (“q”)
“D” Schedule
Section Range (“nnn”)
Enter 001 – 050
Code “cc” Description
00 Schedule in Schedule
01 15 minutes prior to In Schedule
(opening)
02 15 minutes prior to Out of Schedule
(closing)
03 Holiday in Effect (Whether Type 1,2,3 or
No Access)
04 No Access, Holiday in effect.
Program Section (“q”)
“H” oliday
Section Range (“nnn”)
Enter 001 – 032
Code “cc” Description
00 Holiday in Effect (Whether type 1,2, 3 or
No Access)
Program Section (“q”)
“A” rea
Section Range (“nnn”)
Enter 001 – 016
Code “cc” Description
00 Function Key 0
01 Function Key 1
02 Function Key 2
03 Function Key 3
04 Function Key 4
05 Function Key 5
06 Function Key 6
07 Function Key 7
08 Function Key 8
09 Function Key 9
10 When area is ON
11 When Area WAS IN ALARM. This is
only for input points in alarm e.g. NOT
for system trouble (clears when alarmed
areas are turned off)
12 When area is in STAY 1
13 When area is in STAY 1 or (2 future)
14 When area is OFF
15 When area is Not ON
16 When area is Not OFF
17 When area is in ALARM. Resets when
point(s) restore or follows siren timeout
(includes equipment failures & tampers)
18 When area WAS IN ALARM. This is only
for input points in alarm e.g. NOT for
system trouble (clears when alarmed
areas are turned off then back on again)
19 Follows ALARM siren - steady for BURG
/ EMERG and provides 1 sec ON/OFF
for FIRE
20 Follows ALARM siren - steady for BURG
/ EMERG and provides 2 sec ON/OFF
for FIRE
21 Follows sonalert, chime & provides
Entry/Exit tones when armed to STAY &
ON (UK ACPO = Fail to Arm)
22 Follows sonalert, chime & does not
provide Entry/Exit tones when armed to
STAY but provides Entry/Exit tones in
ON (UK ACPO = Fail to Arm)
23 Follows Garage Entry Tones
24 When any point in this area is
BYPASSED
25 When any ‘FIRE’ type point in this area
is in alarm
26 When any ‘HOLD UP’ type point in this
area is in alarm
27 When any ‘AUXILIARY ALERT’ type
point in this area is in alarm.
28 When any ‘VAULT / SAFE’ type point is
in alarm.
29 When any ‘BURGLARY’ type point in
this area is in alarm.
30 When any ‘Supervisory' point is in alarm.
31 When any ‘Equipment Failure' is in
alarm.
32 Area is in ‘Walk’ or ‘Hold-up’ test.
33 When area Entry / Exit delay is in
progress – provides a steady output
(STAY & ON).
34 When area Entry delay is in progress -
provides a steady output (STAY & ON).
35 When area Exit delay is in progress -
provides a steady output (STAY & ON).
36 When the area is ‘Ready To Arm’ - i.e.
all points are secure.
37 When the area’s active schedule is in
effect.
38 When the area schedule is CLOSING in
15 minutes.
39 Doors Unlocked.