Great Planes ESP6 Easy Sport 60 - GPMA0152 - Manual (Page 7)

D Four-channel Radio With 4 Servos
D Engine (see page 4)
D Glow Plug (see engine instructions)
D Propeller (see engine instructions for sizes)
D 1/4" Thick Foam Rubber (HCAQ1000)
D 12" Silicone Fuel Tubing (GPMQ4131)
Accessories Required to Complete Your Easy Sport 40
D 2-1/2" Spinner (GPMQ4520)
D 10oz. Fuel Tank (GPMQ4104)
D (3) 2-1/2" Wheels (GPMQ4223)
D Wheel Collars (2ea ) 5/32" (GPMQ4306)
(4ea)3/16"(GPMQ4308)
D (2 rolls) Covering Top Flite MonoKote
D Optional: Wire Tail Gear Assembly (GPMQ1900)
D 1" Tail Wheel (GPMQ4241)
D (2) 3/32" Wheel Collar (GPMQ4302)
D Pilot 1-1/2" Scale
D Great Planes Easy Sport Trim Graphics
(GPMQ0405)
Accessories Required to Complete Your Easy Sport 60
D 2-3/4" Spinner (GPMQ4525)
D 14oz Fuel Tank (GPMQ4106)
D (3) 3" Wheels (GPMQ4224)
D 3/16" Wheel Collars (6 ea ) (GPMQ4308)
D (3 rolls) Covering Top Flite MonoKote recommended
D Optional: Wire Tail Gear Assembly (GPMQ1900)
D 1-1/2" Tail Wheel (GPMQ4243)
D (2) 3/32" Wheel Collar (GPMQ4302)
D Pilot 1-1/2" Scale
We recommend Great Planes Pro CA and Epoxy
adhesives
D 2oz. CA (Thin) (GPMR6003)
D 2oz. CA+ (Medium) (GPMR6009)
D 1oz. CA- (Thick) (GPMR6014)
D 6-Minute Epoxy (GPMR6045)
D 30-Minute Epoxy (GPMR6047)
D Hand or Electric Drill
D 5/32"
D 3/16"
D 1/4"
D 15/64"
D 19/64"
Drill Bits.
D 1/16"
D 5/64"
D
1/8"
D 7/64"
D 9/64"
D String
D Building Square: (XACR7726)
D Building Triangle: (XACR7725)
D Straightedge With Scale
D Masking Tape
D Waxed Paper or Plastic Kitchen Wrap
D HobbyLite" Balsa Filler (HCAR3401)
D Petroleum Jelly
D Easy-Touch" Bar Sander and Sandpaper see the
following Expert Tip
D Dremel MultiPro'" or similar (Optional)
D 1/8" x 2" Brass Tube (Optional)
D Sealing Iron (TOPR2100)
D Heat Gun (TOPR2000)
D Hobby Saw (XACR1435)
D #1 Hobby Knife (XACR4305)
D #11 Blades (HCAR0311, 100qty.)
D Razor Plane (MASR1510)
D Pliers
D Screwdrivers (Phillips and Flat Blade)
D T-Pins: short (HCAR5100) and long (HCAR5200)
To build the Easy Sport, you will need a 15" x 48"
(minimum size) flat surface Because your model will be
no straighter than this surface, it is critical that it is
truly flat
The surface of the work area should be of a
material that you can push pins into, such as a piece of
7