Kontron VM162 User Manual

Kontron Hardware

Text mode
Original mode

VM162/VM172

VMEbus Single-Board Computer with

Manual Order Nr. 16596

User’s Manual

Issue 1

Dual IndustryPack Support

This manual is related to the following products:

VM172

Table of contents

Document Outline

Introduction 1-1
Functional Description 2-1
Configuration 3-1
Programming 4-1
Unpacking and Special Handling Instructions
Revision History
PEP Modular Computers Two Year Limited Warranty
Preface
1.1 Product Overview
1.2 IndustryPack Flexibility
1.3 Controller eXtension Connector
1.4 Front Panel and I/O Configuration
- Figure 1.1 Front Panel Options
1.5 Features
- Figure 1.2 MC68EN360 Channel Assignment
1.6 Specifications
1.7 Ordering Information
1.8 Related Publications
1.9 Schematic Board Layout
- Introduction
2.1 VM162/VM172 Block Diagram
2.2 CPU Options
- Table 2.1: CPU Options
- 2.3 Memory
- 2.4 Communication Controller 68EN360 (QUICC)
- 2.5 VMEbus Interface
2.6 Board Control Logic
- 2.6.1 Boot Decoder Logic
- 2.6.2 Interrupt Control
- 2.6.3 Bus Timer
- 2.6.4 Watchdog Timer
- 2.6.5 Board Control/Status Register
2.7 Special Functions
- 2.7.1 Real Time Clock
- 2.7.2 Serial EEPROM
- 2.7.3 TICK Timer
- 2.7.4 General Purpose Timer
- 2.7.5 DMA Transfers
- 2.7.6 Data Retention for RTC and SRAM
- 2.7.7 Front Panel Buttons and LED Ports
2.8 Serial Communication Ports
- Figure 2.2 MC68EN360 Channel Assignment
  - Table 2.9: Serial Communication Port Configuration...
- 2.8.1 Ethernet/SER4 Port
- 2.8.2 SER1, SER2 and SER3 Ports
- 2.8.3 TERM Pinout
2.9 CXC Interface
- Table 2.10: CXC Pinouts using the 68(EN)360
- Table 2.11: Further Explanation of 68(EN)360 Mnemo...
2.10 IndustryPack (IP) Interface
- 2.10.1 Overview
- 2.10.2 Features
- 2.10.3 Optional IP features, not supported
- 2.10.4 IP Interface Controller
- 2.10.5 IP Reset Control
- 2.10.6 IP Clock Control
- 2.10.7 IP Interrupt Control
- 2.10.8 IP Memory Size Control
- 2.10.9 IP Interface Address Map
- 2.10.10 IP Interrupt Control Register
- 2.10.11 IP Slot Control Register
- 2.10.12 IP Connectors
3.1 Default Jumper Settings
- 3.1.1 Jumper Default Settings (Component Side)
- 3.1.2 Jumper Default Settings (Solder Side)
3.2 Jumper Description (Component Side)
- Figure 3.1 VM162/VM172 Jumper Layout (Component Si...
- 3.2.1 VME Boot
- 3.2.2 ROM Boot
- 3.2.3 Protective Ground - Signal Ground
- 3.2.4 VME SYSRES*
- 3.2.5 CXC Mode
3.3 Jumper Description (Solder Side)
- Figure 3.2 VM162/VM172 Jumper Layout (Solder Side)...
- 3.3.1 CPU Type
- 3.3.2 CPU Power Supply
- 3.3.3 CPU (Bus) Clock
- 3.3.4 SRAM Size
- 3.3.5 Communications Clock
- 3.3.6 EEPROM Write Protection
- 3.3.7 JTAG Chain
- 3.3.8 SRAM Data Retention
- 3.3.9 BERR1 Timeout
- 3.3.10 Backup Current Test Bridge
  - Configuration
4.1 VM162/VM172 Address Map
4.2 Initializing the 68EN360
- 4.3 Initializing the Cache
  - Programming
    - APPENDIX MEMORY PIGGYBACKS
    - Ordering Information
1 DM600
- 1.1 Jumper Location
2 DM601
- 2.1 Jumper Location
3 DM602
- 3.1 Jumper Location
4 DM603
- 4.1 Jumper Location
5 DM604
- 5.1 Jumper Location
  - APPENDIX SI6 PIGGYBACKS
  - Ordering Information
1 SI6-10B2
- 1.1 Specifications
- 1.2 Connector
2 SI6-10B5
- 2.1 Specifications
- 2.2 Connector
3 SI6-10BT
- 3.1 Specifications
- 3.2 Connector
- 3.3 Jumper Location
4 SI6-PB485-ISO
- 4.1 Specifications
- 4.2 Connector
- 4.3 Jumper Location
  - APPENDIX
1 Introduction
2 System Operation
- 2.1 Startup
- 2.2 Entering the Command Mode
3 Programming FLASH Memory
- 3.1 Preparing the Image
- 3.2 Programming with Motorola S-Records
- 3.3 Programming from an Absolute Address
- 3.4 Boot Wait Time
4 Command Reference
- 4.1 Boot Wait
- 4.2 Load Flash
- 4.3 Memory Display
- 4.4 Port Format
- 4.5 Reset System
- 4.6 Help
  - APPENDIX CXC. CONTROLLER EXTENSION CONNECTOR
1 CXC Address Range
2 CXC Generic Pinouts
3 CPU Pinout Cross Reference
- Table 3.0.1: Comparsion of 68302 / 68(EN)360 Funct...
4 Timing
5 Controller Extension Connectors
- APPENDIX OS-9 CABLING
1 OS-9 System <-> Terminal
- 1.1 Software (XON/XOFF) or no Handshake
- 1.2 Hardware Handshake (Set Terminal to CTS/DTR Ha...
  - 1.2.1 15-pin Connector on OS-9 Side
  - 1.2.2 8-pin RJ45 Connector on OS-9 Side (SMART I/O...
2 OS-9 System <-> PC
- 2.1 Software (XON/XOFF) or no Handshake
- 2.2 Hardware Handshake (Select RTS/CTS Handshake o...
3 OS-9 System <-> Modem
- 3.1 15-pin Connector
- 3.2 8-pin RJ45 Connector (SMART I/O)
4 OS-9 System <-> OS-9 System
- 4.1 Software (XON/XOFF) or no Handshake
- 4.2 Hardware Handshake
  - 4.2.1 15-pin Connector
  - 4.2.2 8-pin RJ45 Connector (SMART I/O)