Dell PowerEdge 2550 - Manual (Page 34)

instructions on obtaining technical assistance.
Diskette drive 0 seek failure Faulty or improperly inserted diskette,
incorrect configuration settings in System
Setup program, loose diskette drive
interface cable, or loose power cable Replace the diskette. Run the System Setup program to correct
the diskette drive type. See "Using the System Setup Program"
in the User's Guide for instructions. Check that the diskette
drive/CD-ROM drive unit is seated properly against the
interposer board on the peripheral cage. See "
Installing a
Drive in the Peripheral Bay ."
Diskette read failure Faulty diskette, faulty or improperly
connected diskette drive, or loose power
cable Check that the diskette drive/CD-ROM drive unit is seated
properly against the interposer board on the peripheral cage.
See "
Installing a Drive in the Peripheral Bay ."
Diskette subsystem reset failed Faulty diskette drive controller (defective
system board) Replace the system board. See " Getting Help " for instructions
on obtaining technical assistance.
Diskette write protected Diskette write-protect feature activated Move the write-protect tab on the diskette.
Drive not ready Diskette missing from or improperly
inserted in diskette drive Reinsert or replace the diskette.
Embedded server management error
Embedded server management is not
present
Embedded server management memory
may be temporarily corrupted Shut down the system to clear the memory, and then restart
the system. If the problem persists, see "
Getting Help " for
instructions on obtaining technical assistance.
Gate A20 failure Faulty keyboard controller (defective
system board) Replace the system board. See " Getting Help " for instructions
on obtaining technical assistance.
General failure Operating system corrupted or not
installed properly Reinstall the operating system.
Hard disk controller failure Incorrect configuration settings in System
Setup program, improperly connected
hard-disk drive, faulty hard-disk drive
controller subsystem (defective system
board), or loose power cable Check the hard-disk drive configuration settings in the System
Setup program. See "Using the System Setup Program" in the
User's Guide for instructions. Reinstall the hard-disk drive.
Check the interface cable and power cable connections to the
backplane board. See "
Installing Hard-Disk Drives ."
Invalid configuration information -
please run SETUP program
Incorrect ISA_CLR jumper configuration,
incorrect configuration settings in System
Setup program, or faulty battery Remove the plug from the ISA_CLR jumper. See " Jumpers,
Switches, and Connectors " for instructions. Check the System
Setup configuration settings. See "Using the System Setup
Program" in the User's Guide for instructions. Replace the
battery. See "
Installing System Board Options ."
Invalid CPU speed detected Microprocessor not supported by system Install a correct version of the microprocessor in the specified
microprocessor connector.
Invalid NVRAM configuration,
resource reallocated
System detected and corrected a resource
conflict when system resources were
allocated using the Resource Configuration
Utility No action is required.
I/O parity interrupt at address Expansion card improperly installed or
faulty Reinstall the expansion card. See " Installing System Board
Options ." If the problem persists, replace the expansion card.
Keyboard failure Keyboard cable connector loose or
improperly connected, defective keyboard,
or defective keyboard/mouse controller
(defective system board) Check the keyboard cable connection. Replace the keyboard. If
the problem persists, replace the system board. See "
Getting
Help " for instructions on obtaining technical assistance.
Keyboard controller failure Defective keyboard/mouse controller
(defective system board) Replace the system board. See " Getting Help " for instructions
on obtaining technical assistance.
Keyboard data line failure
Keyboard stuck key failure
Keyboard cable connector loose or
improperly connected, defective keyboard,
or defective keyboard/mouse controller
(defective system board) Check the keyboard cable connection. Replace the keyboard. If
the problem persists, replace the system board. See "
Getting
Help " for instructions on obtaining technical assistance.
Memory address line failure at
address, read value expecting value
Memory double word logic failure at
address, read value expecting value
Memory odd/even logic failure at
address, read value expecting value
Memory write/read failure at
address, read value expecting value
Faulty or improperly seated memory
modules or defective system board Remove and reseat the memory modules. If the problem
persists, replace the memory modules. If the problem still
persists, replace the system board. See "
Getting Help " for
instructions on obtaining technical assistance.
Memory allocation error Faulty application program Restart the application program.
Memory parity interrupt at address Improperly seated or faulty memory
modules Remove and reseat the memory modules. If the problem
persists, replace the memory modules. See "
Getting Help " for
instructions on obtaining technical assistance.
Memory tests terminated by keystroke POST memory test terminated by pressing
the spacebar No action is required.
No boot device available Faulty diskette, diskette drive subsystem,
CD-ROM drive, hard-disk drive, or hard-
disk drive subsystem, or no boot disk in
drive A Replace the diskette drive, CD-ROM, or hard-disk drive. If the
problem persists, replace the system board. See "
Getting Help "
for instructions on obtaining technical assistance.
No boot sector on hard- disk drive Incorrect configuration settings in the
System Setup program Check the hard-disk drive configuration settings in the System
Setup program. See "Using the System Setup Program" in the
User's Guide for instructions.
No timer tick interrupt Defective system board Replace the system board. See " Getting Help " for instructions
on obtaining technical assistance.