Great Plains 2007HD Update Installation User Manual

369a update installation, Manufacturing, inc

Text mode
Original mode

Manufacturing, Inc.

www.greatplainsmfg.com

Printed 05/25/2011

166-370M

166-369A Update Installation

NTA607HD or NTA2007HD

6 Meter No-Till Air Drills

Read the update manual entirely. When you see this symbol, the
subsequent instructions and warnings are serious - follow without
exception. Your life and the lives of others depend on it!

Illustrations may show optional equipment not supplied with standard unit.

32109

This manual is related to the following products:

NTA607HD Update Installation

Table of contents

Document Outline

166-369A Update Installation
Table of Contents
Important Safety Information
- Look for Safety Symbol
- Be Aware of Signal Words
- Prepare for Emergencies
- Avoid High Pressure Fluids
- Be Familiar with Safety Decals
General Information
- Related Documents
- Notations and Conventions
  - Call-Outs
- Tools Required
- Regarding Parts
  - About New Parts
  - About Existing Parts
- Pre-Assembly Preparation
  - Work Location
Update Underside Weldments
- Configure Implement
- Tack Rear Bottom Gussets
  - LH Rear Bottom Gussets
  - RH Rear Bottom Gussets
- Install Nut Blocks
- Install Box Plates
- Install Corner Gussets
Disconnect Implement
- Prepare Implement
- Disconnect Primary Hoses
- Clear Weight Transfer Cylinders
- Clear Link Lift Cylinders
- Recover Pull Link Components
- Release Lift-Assist Link
- Uncouple Cart
- Remove Pull Link
Dismount Hoppers
- Disconnect Sensors and Chain
- Dismount Meters
  - Disconnect Meter Inlet Elbows
  - Remove Meters
- Hoist Hoppers
  - Release Hopper Mount
  - Remove Hopper Assembly
Update Meters
- Remove Existing Top Seal
- Remove Meter Flute Shaft
  - Remove Old Flanges
- Enlarge Mounting Slots
- Drill Weep Holes
- Install Meter Seal Flange
- Replace Meter Shaft Mount Plates
Update Cart
- Cart Frame Update Overview
- Install Rear Gussets
  - Install Left Rear Gusset
  - Install Right Rear Gusset
- Install Front Gussets
  - Install Right Front Gusset
  - Install Left Front Gusset
- Install Pull Bar Attach Points
  - Install Pull Bar Plate
  - Install Pull Bar Anchors
    - Install Left Anchor
    - Install Right Anchor
- Update Meter Mounts
- Re-Install Meters
  - Install Hopper Supports
- Install Pull Bars
  - Assemble Pull Bars
  - Attach Pull Bars
- Update Cart Hydraulics
- Re-Install Hoppers
- Update Hopper Lids
Update Implement Frame
- Dismount Lift-Assist
- Update Rear Link Anti-Rotation
- Update Wing Pivot Anti-Rotation
- Update Wing Pivot Extension Tops
  - Update Front Extension Tops
  - Update Rear Extension Tops
Update Harness
- Dismount Existing Harnesses
- Enumerate WSMBs
- Install WSMBs
  - Mount Center WSMBs
    - Mount Tower B WSMB
    - Mount Tower C WSMB
  - Mount Wing WSMBs
    - Mount Tower A (Left Wing) WSMBs
    - Mount Tower D (Right Wing) WSMBs
- Install Row Harnesses
Install Rear Pull Link
- Pin Link to Main Frame
- Connect Lift-Assist Link
- Connect Lift Assist
- Re-Install Parallel Arms
- Re-Connect Lights
Update Implement Hydraulics
- Extend Valve Hoses
- Relocate Valve Group
- Protect Hose Extensions
Re-Hitch Implement
- Install Front Pull Link
- Re-Connect Lift Link
- Connect Cart and Implement
- Re-Install Link Components
  - Store Spacers
  - Store New Lift Pins
- Re-Install Link Lift Cylinders
- Re-Install Weight Transfer Cylinders
- Route Hoses and Harnesses
  - Hose ID for Pull Link Clamping
- Connect Hoses and Harnesses
Update Markers
- Remove Tension Spring
- Release Swing Pivot
- Release Cylinder
- Remove Arm
- Remove Old Pivot Frame
- Install New Pivot Frame
- Re-Install Arm
- Re-Attach Spring
Update Coulters
- Prepare Implement
- Replace Coulter Bars
  - Remove Existing Bar
  - Install New Bar
Close-Out
- Reconfigure Monitor
Appendix A - Reference Information
- Chain Setup
  - Chain Clip Orientation
  - Chain Slack
- Torque Values Chart
- Hydraulic Connectors and Torque
Appendix D - Drawings
- 160-795D PIN RETAINER TAB
- 160-801D FRAME NUT BLOCK
- 160-802D FRAME EXT BOT GUSSET LH REWORK
- 160-803D FRAME EXT BOX PLATE
- 160-804D FRAME EXT BOT GUSSET LH REWORK
- 160-805D FRAME EXT BOT GUSSET REWORK
- 160-806D FRAME EXT BOT GUSSET REWORK
- 160-807D FRAME EXT CORNER GUSSET
- 160-808D FRAME EXT 100 DEG GUSSET
- 160-809D FR EXT 100 DEG GUSSET REWORK
- 160-810D FR EXT 100 DEG GUSSET REWORK
- 160-811D WING HINGE PIN ROTATION STOP
Appendix G - Glossary
- Part Descriptor Abbreviations
Appendix H - Harness
- Tower ID
- Secondary Hose Routing, 40-Row
- Harness (LH)
- Harness (RH)
Appendix P - Part Lists
- Existing Parts Affected
- 166-369A New Parts
Index