Great Plains 2510HDP Operator Manual User Manual
Operator manual, Manufacturing, inc
Table of contents
Document Outline
- Operator Manual
- Table of Contents
- Important Safety Information
- Look for Safety Symbol
- Be Aware of Signal Words
- Prepare for Emergencies
- Be Familiar with Safety Decals
- Avoid High Pressure Fluids
- Wear Protective Equipment
- Keep Riders Off Machinery
- Use Safety Lights and Devices
- Transport Machinery Safely
- Check for Overhead Lines
- Handle Chemicals Properly
- Shutdown and Storage
- Practice Safe Maintenance
- Tire Safety
- Safety At All Times
- Safety Reflectors and Decals
- Slow Moving Vehicle Reflector 818-055C
- Red Reflectors 838-266C
- Amber Reflectors (large) 838-265C
- Amber Reflectors, small (Option) 818-229C
- Daytime Reflectors 838-267C
- Danger: Cannot Read English 818-557C
- Danger: Crushing Hazard 818-590C
- Warning: Excessive Speed Hazard 818-337C
- Warning: High Pressure Fluid 818-339C
- Warning: Marker Pinch Crush (Option) 818-682C
- Warning: Falling Hazard 838-102C
- Caution: Tires Not A Step 818-398C
- Caution: Read Manual 818-587C
- Caution: 32 PSI Tire Pressure 818-751C
- Caution: 52 PSI Tire Pressure 818-752C
- Caution: 36 PSI Tire Pressure 818-855C
- Introduction
- Preparation and Setup
- Operating Instructions
- Adjustments
- Planting Depth
- Material Rate Adjustments
- Row Unit Adjustments
- Marker Adjustments
- Hydraulic Drive Operation
- Drive Operational Requirements
- Tractor Hookup
- Controller Menu
- Console Functions
- Calibration
- Speed Calibration
- Operations
- Varying Rates with Pre-set Function
- GPS-Based Planting
- Hydraulic Drive Maintenance
- Hydraulic Drive Troubleshooting
- Hydraulic Drive Troubleshooting Flow Chart
- Hydraulic Drive Electronics Troubleshooting
- Troubleshooting
- Maintenance and Lubrication
- Materials Clean-Out
- Meter Maintenance
- Row Unit Maintenance
- Chain Maintenance
- Marker Maintenance
- Lubrication
- Gauge Wheel Arm Pivots
- Marker Hinge Points (option)
- Small Seeds Meter Shaft Bearing
- Fertilizer Shaft Bearings
- Fertilizer Felt Barrier Seals
- Meter Drive Chains
- Gauge Wheel & Main Box Chains
- Second Box Chains
- Third Box Chains
- Single Gauge Wheel Bearings
- Offset Single Gauge Wheel Bearings
- Dual Gauge Wheel Bearings
- Marker Disk Bearings
- Options
- Appendix
- Specifications and Capacities
- Tire Inflation Chart
- Torque Values Chart
- Row Spacing Data
- Example Row Spacing
- Row Spacing Data Legend
- Model 1510HDP Row Spacings
- 1510HDP-12TR Standard Spacing
- 1510HDP-12TR as “1510HDP-0630”
- 1510HDP-1315 Standard Spacing
- 1510HDP-1315 as “1510HDP-0730”
- 1510HDP-1315 as “1510HDP-0630”
- 1510HDP-1910 Standard Spacing
- 1510HDP-1910 as “1510HDP-1020”
- 1510HDP-1910 as “1510HDP-0730”
- 1510HDP-1910 as “1510HDP-0630”
- 1510HDP-1910 as “1510HDP-0540”
- 1510HDP-19TRS Standard Spacing
- 1510HDP-19TRS as “1510HDP-12TR30”
- 1510HDP-19TRS as “1510HDP-0730”
- 1510HDP-19TRS as “1510HDP-0630”
- 1510HDP-2475 Standard Spacing
- 1510HDP-2475 as “1510HDP-1215”
- 1510HDP-2475 as “1510HDP-12TR30”
- 1510HDP-2475 as “1510HDP-0630”
- Model 2010HDP Row Spacings
- 2010HDP-16TR Standard Spacing
- 2010HDP-16TR as “2010HDP-0830”
- 2010HDP-1715 Standard Spacing
- 2010HDP-1715 as “2010HDP-0930”
- 2010HDP-1715 as “2010HDP-0830”
- 2010HDP-2510 Standard Spacing
- 2010HDP-2510 as “2010HDP-1320”
- 2010HDP-2510 as “2010HDP-1220”
- 2010HDP-2510 as “2010HDP-0930”
- 2010HDP-2510 as “2010HDP-0830”
- 2010HDP-2510 as “2010HDP-0740”
- 2010HDP-25TRS Standard Spacing
- 2010HDP-25TRS as “2010HDP-16TR30”
- 2010HDP-25TRS as “2010HDP-0930”
- 2010HDP-25TRS as “2010HDP-0830”
- 2010HDP-3275 Standard Spacing
- 2010HDP-3275 as “2010HDP-1615”
- 2010HDP-3275 as “2010HDP-16TR30”
- 2010HDP-3275 as “2010HDP-0830”
- Model 2510HDP Row Spacings
- 2510HDP-2015 Standard Spacing
- 2510HDP-2015 as “2510HDP-1030”
- 2510HDP-20TR30 Standard Spacing
- 2510HDP-20TR30 as 2510HDP-1030
- 2510HDP-2910 Standard Spacing
- 2510HDP-2910 as “2510HDP-1520”
- 2510HDP-2910 as “2510HDP-1420”
- 2510HDP-2910 as “2510HDP-1030”
- 2510HDP-2910 as “2510HDP-0840”
- 2510HDP-29TRS Standard Spacing
- 2510HDP-29TRS as “2510HDP-20TR30”
- 2510HDP-29TRS as “2510HDP-1030”
- 2510HDP-4075 Standard Spacing
- 2510HDP-4075 as “2510HDP-2015”
- 2510HDP-4075 as “2510HDP-20TR30”
- 2510HDP-4075 as “2510HDP-1030”
- Hydraulic Diagrams
- Chain Routing
- Warranty
- Index