SoundOff Signal nFORCE® Interior Traffic Controller - Manual (Page 6)

IMPORTANT INFORMATION:
Warning devices are strictly regulated and governed by Federal, State and Municipal ordinances. These devices shall be used ONLY on approved vehicles. It is the sole responsibility of the user of these devices to ensure compliance.
To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at www.soundoffsignal.com/sales-support.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. at 1.800.338.7337 (press #4 to skip the automated message).
Questions or comments that do not require immediate attention may be emailed to [email protected].
SUPERIOR CUSTOMER RELATIONSHIPS. SMARTLY DESIGNED LIGHTING & ELECTRONIC SOLUTIONS.
nFORCE® LED Traffic Controller - Interior Use Only
ENFTCDGS12(xx)
nFORCE Traffic Controller 9.14
ELECTRICAL INSTALLATION (CONTINUED)
6.
NOTE: For settings below, Switch #2 does not need to be moved to the up position after each configuration. The switch can
remain in the down position until the lightbar is completely configured and then moved to the Up position to store all the settings.
Cruise Mode Configuration:
a. Set Switch #2 on Breakout box to down position (Switch #1 must be in Up position)
b. Determine which module inputs are needed for cruise mode
c. Apply voltage to the Cruise Mode activation wire
d. Apply voltage to the light group wire(s) required (i.e. Front Corner, Front Inboard 1, etc.)
e. Momentarily apply voltage to the pattern select wire to change the color between Off, Color 1, Color 2, and Color 3.
NOTE: If configuring a single color or dual color module, make sure the chosen color is configured for Off and not a color which does not
exist on the module. The lightbar will flash color #1 of all modules configured for cruise mode. If a module flashes every 2 seconds and is
not intended to be on when Cruise mode is activated, repeat steps ‘d’ and ‘e’ until module no longer flashes.
f. Set Switch #2 on Breakout box to up position to save settings and return light-bar to normal operating mode
Takedown and Work-light Configuration:
a. Set Switch #2 on Breakout box to down (Switch #1 must be in Up position)
b. Determine which module inputs are needed for Takedowns or Work-lights
c. Apply voltage to the Takedown activation wire
d. Apply voltage to the light group wire(s) required (i.e. Front Inboard 1, Rear Inboard 2, etc.)
e. Momentarily apply voltage to the pattern select wire to change the color between Off, Color 1, Color 2, and Color 3.
NOTE: If configuring a single color or dual color module, make sure the chosen color is configured for Off and not a color which does not ex-
ist on the module. The light-bar will flash color #1 of all modules configured for takedown. If a module flashes every 2 seconds and is not
intended to be on when takedown is activated, repeat steps ‘d’ and ‘e’ until module no longer flashes.
f. Set Switch #2 on Breakout box to up position to save settings and return light-bar to normal operating mode
Scene light Configuration:
a. Set Switch #2 on Breakout box to down (Switch #1 must be in Up position)
b. Determine which module inputs are needed for Scene Lighting
c. Apply voltage to the Scene light activation wire
d. Apply voltage to the light group wire(s) required (i.e. Front Inboard 1, Rear Inboard 2, etc.)
e. Momentarily apply voltage to the pattern select wire to change the color between Off, Color 1, Color 2, and Color 3.
NOTE: If configuring a single color or dual color module, make sure the chosen color is configured for Off and not a color which does not
exist on the module. The light-bar will flash color #1 of all modules configured for scene light. If a module flashes every 2 seconds and is
not intended to be on when scene light function is activated, repeat steps ‘d’ and ‘e’ until module no longer flashes.
f. Set Switch #2 on Breakout box to up position to save settings and return light-bar to normal operating mode