SoundOff Signal SkyFire LED - Manual

Skyfire™ LED Lightbar Owner's Manual ESF1ØØØ.pdf ~ Rev. 01.12 Pg. 1
To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product please visit our website.
If you have questions regarding this product please contact Technical Services, Monday - Friday, 8 am to 5 pm at
1.800.338.7337, press #4 to skip the automated message. Questions or comments that do not require immediate attention may
be emailed to [email protected].
1.800.338.7337. / www.soundoffsignal.com / Thank you for trusting us with your safety!
#ESF1 ØØØ Skyfire™ LED Lightbar
TABLE OF CONTENTS:
1 IMPORTANT NOTICE, COMPONENT LIST, POWER
SPECIFICATIONS & TECHNICAL SPECIFICATIONS
2 VISUAL ASSEMBLY, PARTS LIST AND MODULE
REPLACEMENT/RECONFIGURATION INSTRUCTIONS
3 FLASH PATTERN PROGRAMMING INSTRUCTIONS, FLASH
PATTERN LIST AND WIRE HARNESS DESIGNATIONS
4 CLEANING & CARE INSTRUCTIONS, WARNINGS,
REPLACEMENT AND WARRANTY INFORMATION
INSTALLATION:
1) Brackets are sold separately. Refer to specific bracket
instructions for mounting.
2) Route wires to control box. NOTE: Installation of this
lightbar must NOT encroach on Air-Bag Deployment Zone.
If in doubt, installer should consult vehicle manufacturer.
3) Use a grommet (installer supplied) or other adequate
protection to prevent wire from being abraded or damaged.
Eliminate all sharp edges.
• Warning devices are strictly regulated and governed by Federal, State and
Municipal ordinances. These devices shall be used ONLY on approved
vehicles. It is the sole responsibility of the user of these devices to ensure
compliance.
• DO NOT install this product or route any wires in the Air Bag Deployment
Zone. Refer to your vehicle Owner’s Manual for the location of any air bag
deployment zones.
• DO NOT connect this device to a strobe power supply. This product is
self-contained and does not require an external power supply.
Important Information:
!
WARNING
This product contains high intensity LED devices. To
prevent eye damage, DO NOT stare into the light
beam at close range.
IMPORTANT NOTICE TO INSTALLER: Make sure to read and understand
all instructions and warnings before proceeding with the installation of this
product. Ensure that the manual and any warning cards are delivered to the
end user of this equipment. Proper installation of the lightbar requires the
installer to have a thorough knowledge of automotive electronics, systems,
and procedures. Lightbars provide an essential function of an effective visual
warning system. The use of the lightbar does not insure that all drivers can
or will abide by or react to an emergency warning signal, especially at high
rates of speeds or long distances. The operator of the vehicle must never take
the right of way for granted and it is the operator’s responsibility to proceed
safely. The effectiveness of the this lightbar is highly dependant on the correct
mounting and wiring. The installer must read and follow the manufacturer’s
installation instructions and warnings in the manual. The vehicle operator
should verify daily that the lightbar is securely fastened to the vehicle and
properly functioning before operating vehicle. The lightbar is intended for use
by authorized personnel only. It is the user’s responsibility to ensure they
understand and operate the emergency warning devices in compliance with
the applicable city, state and federal laws and regulations. SoundOff Signal
assumes no liability for any loss resulting from the use of this warning device.
Components/Contents
Standard Equipment:
1 - SKYFIRE™ LED Lightbar built to your specifications
Other Parts that may be included depending on your configuration:
1 - Vehicle Specific Hook Kit w/ Hardware*
2 - Fixed Height Mounting Brackets w/ Hardware or
1 - Flat Mount Hardware Kit or
2 - Headache Brackets w/ Hardware
*Kits will vary with each lightbar depending on vehicle specified on order form.
Unpack Lightbar
1. Remove the lightbar from box and packaging.
2. Save packaging for later shipping.
3. Check components/contents.
4. Please reference these instructions for proper wiring and installation.
Tools Required for Installation
• 1/2“” Socket with ratchet or 1/2“ box end
• Phillips Head Screwdriver
POWER SPECIFICATIONS
Input Voltage Range: 10 -16 Vdc
Current Draw in Amps (A) @ 12.8 Vdc:
Flashing Steady On Power Consumption
Warning Module 0.5A 1A 6 watts
Stop/Turn/Tail Module
Stop/Turn: 0.11 mA
Tail: 25 mA
0.46 mA
Stop/Turn: 1.5 watts
Tail: 0.3 watts
LED
Take Down/Work Light
1A 1A 12.8 watts
Halogen
Take Down/Work Light
2.6A 2.6A 35 watts
LED Lightbar
tm
TECHNICAL SPECIFICATIONS
Overall Dimensions:
3” (76 mm) H x 11.25” (29 cm) D
Available Lengths:
48” (122 cm), 55” (140 cm)
or 60” (152 cm)
Flash Patterns: 27 flash patterns
Input Voltage Range: 10-16 Vdc
Current Consumption: <6 amps
Operating Temperature: -40º to +70º C