Lenze ESV SMV frequency inverter - Manual (Page 55)

Lenze SMVector 13465100 EDBSV01 EN v18 53
Commissioning
Code Possible Settings
IMPORTANT
No. Name Default Selection
Segment #15
P780 Segment #15
Frequency Setpoint 0.0 -500.0 {Hz} 500.0 If P112 = 1, negative sign forces reverse
direction
P781 Segment #15
Accel/Decel Time 20.0 0.0 {sec} 3600.0
P782 Segment #15
Time in current step 0.0
0
0.0 {P708} 6553.5
0 {P708} 65535
Scaling/units depend on P708
Skip segment if time = 0
P783 Segment #15
Digital Output State 0
Value set in P783 0 1 2 3 4 5 6 7
Relay (Bit 0) 0 1 0 1 0 1 0 1
TB14 (Bit 1) 0 0 1 1 0 0 1 1
I/O option Relay (Bit 2) 0 0 0 0 1 1 1 1
NOTE: P441 is the Relay Output (TB-19, 20, 21) of the
optional Digital I/O module (ESVZAL0, ESVZAL1).
bit = 0: OFF (De-energized)
bit = 1: ON (Energized)
The corresponding digital output/relay must be
set to accept data from the sequencer: P140,
P142, P441 = 27
P784 Segment #15 TB30
Analog Output
Value 0.00 0.00 {VDC} 10.00 TB30 configuration parameter must be set to
accept this value: P150 = 10
Segment #16
P785 Segment #16
Frequency Setpoint 0.0 -500.0 {Hz} 500.0 If P112 = 1, negative sign forces reverse
direction
P786 Segment #16
Accel/Decel Time 20.0 0.0 {sec} 3600.0
P787 Segment #16
Time in current step 0.0
0
0.0 {P708} 6553.5
0 {P708} 65535
Scaling/units depend on P708
Skip segment if time = 0
P788 Segment #16
Digital Output State 0
Value set in P788 0 1 2 3 4 5 6 7
Relay (Bit 0) 0 1 0 1 0 1 0 1
TB14 (Bit 1) 0 0 1 1 0 0 1 1
I/O option Relay (Bit 2) 0 0 0 0 1 1 1 1
NOTE: P441 is the Relay Output (TB-19, 20, 21) of the
optional Digital I/O module (ESVZAL0, ESVZAL1).
bit = 0: OFF (De-energized)
bit = 1: ON (Energized)
The corresponding digital output/relay must be
set to accept data from the sequencer: P140,
P142, P441 = 27
P789 Segment #16 TB30
Analog Output
Value 0.00 0.00 {VDC} 10.00 TB30 configuration parameter must be set to
accept this value: P150 = 10
End Segment
P790 End Segment:
Frequency Setpoint 0.0 -500.0 {Hz} 500.0 If P112 = 1, negative sign forces reverse
direction
P791 End Segment:
Accel/Decel Time 5.0 0.0 {sec} 3600.0
P792 End Segment: Delay
before P793, 794 &
795 activation 0.0 {P708} 6553.5
0 {P708} 65535
Scaling/units depend on P708
P793 End Segment:
Digital Output State
Value set in P793 0 1 2 3 4 5 6 7
Relay (Bit 0) 0 1 0 1 0 1 0 1
TB14 (Bit 1) 0 0 1 1 0 0 1 1
I/O option Relay (Bit 2) 0 0 0 0 1 1 1 1
NOTE: P441 is the Relay Output (TB-19, 20, 21) of the
optional Digital I/O module (ESVZAL0, ESVZAL1).
bit = 0: OFF (De-energized)
bit = 1: ON (Energized)
The corresponding digital output/relay must be
set to accept data from the sequencer: P140,
P142, P441 = 27