Lenze ESV SMV frequency inverter - Manual (Page 51)

Lenze SMVector 13465100 EDBSV01 EN v18 49
Commissioning
Code Possible Settings
IMPORTANT
No. Name Default Selection
Segment #3
P720 Segment #3
Frequency Setpoint 0.0 -500.0 {Hz} 500.0 If P112 = 1, negative sign forces reverse
direction
P721 Segment #3
Accel/Decel Time 20.0 0.0 {sec} 3600.0
P722 Segment #3
Time in current step 0.0
0
0.0 {P708} 6553.5
0 {P708} 65535
Scaling/units depend on P708
Skip segment if time = 0
P723 Segment #3
Digital Output State 0
Value set in P723 0 1 2 3 4 5 6 7
Relay (Bit 0) 0 1 0 1 0 1 0 1
TB14 (Bit 1) 0 0 1 1 0 0 1 1
I/O option Relay (Bit 2) 0 0 0 0 1 1 1 1
NOTE: P441 is the Relay Output (TB-19, 20, 21) of the
optional Digital I/O module (ESVZAL0, ESVZAL1).
bit = 0: OFF (De-energized)
bit = 1: ON (Energized)
The corresponding digital output/relay must be
set to accept data from the sequencer: P140,
P142, P441 = 27
P724 Segment #3 TB30
Analog Output
Value 0.00 0.00 {VDC} 10.00 TB30 configuration parameter must be set to
accept this value: P150 = 10
Segment #4
P725 Segment #4
Frequency Setpoint 0.0 -500.0 {Hz} 500.0 If P112 = 1, negative sign forces reverse
direction
P726 Segment #4
Accel/Decel Time 20.0 0.0 {sec} 3600.0
P727 Segment #4
Time in current step 0.0
0
0.0 {P708} 6553.5
0 {P708} 65535
Scaling/units depend on P708
Skip segment if time = 0
P728 Segment #4
Digital Output State 0
Value set in P728 0 1 2 3 4 5 6 7
Relay (Bit 0) 0 1 0 1 0 1 0 1
TB14 (Bit 1) 0 0 1 1 0 0 1 1
I/O option Relay (Bit 2) 0 0 0 0 1 1 1 1
NOTE: P441 is the Relay Output (TB-19, 20, 21) of the
optional Digital I/O module (ESVZAL0, ESVZAL1).
bit = 0: OFF (De-energized)
bit = 1: ON (Energized)
The corresponding digital output/relay must be
set to accept data from the sequencer: P140,
P142, P441 = 27
P729 Segment #4 TB30
Analog Output
Value 0.00 0.00 {VDC} 10.00 TB30 configuration parameter must be set to
accept this value: P150 = 10
Segment #5
P730 Segment #5
Frequency Setpoint 0.0 -500.0 {Hz} 500.0 If P112 = 1, negative sign forces reverse
direction
P731 Segment #5
Accel/Decel Time 20.0 0.0 {sec} 3600.0
P732 Segment #5
Time in current step 0.0
0
0.0 {P708} 6553.5
0 {P708} 65535
Scaling/units depend on P708
Skip segment if time = 0
P733 Segment #5
Digital Output State 0 Value set in P733 0 1 2 3 4 5 6 7
Relay (Bit 0) 0 1 0 1 0 1 0 1
TB14 (Bit 1) 0 0 1 1 0 0 1 1
I/O option Relay (Bit 2) 0 0 0 0 1 1 1 1
NOTE: P441 is the Relay Output (TB-19, 20, 21) of the
optional Digital I/O module (ESVZAL0, ESVZAL1).
bit = 0: OFF (De-energized)
bit = 1: ON (Energized)
The corresponding digital output/relay must be
set to accept data from the sequencer: P140,
P142, P441 = 27
P734 Segment #5 TB30
Analog Output
Value 0.00 0.00 {VDC} 10.00 TB30 configuration parameter must be set to
accept this value: P150 = 10