Agilent Technologies VXI E1439 - Manual (Page 79)

69
Agilent E1439 Programmer's Reference
Functions listed alphabetically
with other fiber interfaces before data acquisition begins.
age1439_fiber_xmt_signals (on page 118) −sets the transmitted values of any PIO1,
PIO2, DIR or, NRDY FPDP control signals on the fiber transmitter.
age1439_fiber_xmt_signals_get (on page 118)
−displays the current value of PIO1,
PIO2, DIR and NRDY bits on the fiber transmitter.
age1439_filter_bw (on page 120)
−selects a signal filter bandwidth
age1439_filter_bw_get (on page 120)
−gets the signal filter bandwidth
age1439_filter_decimate (on page 120)
−enables/disables and extra factor of 2 decima-
tion
age1439_filter_decimate_get (on page 120)
−gets current state of extra decimation
age1439_filter_setup (on page 120)
−sets the digital filter bandwidth and decimation fil-
ter parameters
age1439_filter_sync (on page 123)
−synchronizes the decimation filter counter
age1439_frequency_center (on page 128)
−sets the center frequency
age1439_frequency_center_get (on page 128)
−gets the current center frequency
age1439_frequency_center_raw (on page 125) −quickly sets the center frequency
age1439_frequency_center_raw_compute (on page 127)
−quickly calculates the values
for age1439_frequency_center_raw
age1439_frequency_center_raw_get (on page 125)
−gets the raw center frequency
age1439_frequency_cmplxdc (on page 128)
−selects a complex baseband measurement
age1439_frequency_cmplxdc_get (on page 128)
−gets the state of the baseband measure-
ment mode
age1439_frequency_setup (on page 128)
−sets all the zoom center frequency parameters
age1439_frequency_sync (on page 128)
−prepares the module for a synchronous fre-
quency change
age1439_frequency_sync_get (on page 128)
−gets the state of the synchronous change
mode
age1439_front_panel_clock_input (on page 131)
−specifies the source of the front panel
clock
age1439_front_panel_clock_input_get (on page 131)
−gets the front panel clock source
age1439_init (on page 132)
−initializes the I/O driver for a module
age1439_input_alias_filter (on page 141)
−include/bypass the built-in analog anti-alias
filter
age1439_input_alias_filter_get (on page 141)
−gets the anti-alias filter state
age1439_input_autozero (on page 134)
−nulls out the input dc offset in baseband mode
age1439_input_coupling (on page 141)
−selects ac or dc input coupling
age1439_input_coupling_get (on page 141)
−get the input coupling type
age1439_input_offset (on page 135)
−sets the dc offset settings for the current range
age1439_input_offset_get (on page 135)
−gets the dc offset settings
age1439_input_offset_save (on page 136)
−saves the dc offset settings in NVRAM
age1439_input_range (on page 141)
−sets the full scale range
age1439_input_range_auto (on page 137)
−performs auto-ranging in baseband mode
age1439_input_range_convert (on page 138) −converts the input range to volts
age1439_input_range_get (on page 141)
−gets the input range
age1439_input_setup (on page 141)
−sets all the analog input parameters
age1439_input_signal (on page 141)
−connect/disconnect the input signal to the input
amplifiers
age1439_input_signal_get (on page 141)
−gets the input buffer amplifier state
age1439_input_signal_path (on page 141)
−selects baseband or IF signal path
age1439_input_signal_path_get (on page 141) −gets the signal path state
age1439_interrupt_mask_get (on page 146)
−gets the interrupt event mask
age1439_interrupt_priority_get (on page 146)
−gets the VME interrupt line