Agilent Technologies VXI E1439 - Manual (Page 78)

68
Agilent E1439 Programmer's Reference
Functions listed alphabetically
age1439_driver_debug_level_get (on page 97)
−gets the debug level
age1439_epoch_generate (on page 98) −controls whether or not data epochs are gener-
ated.
age1439_epoch_generate_get (on page 98)
− gets the current value of epochGenerate
age1439_epoch_header (on page 98)
−sets the value of the first 32 bits of the epoch
header. It can be used by the optical receiver to direct where to route and/or how to
process associated epoch data.
age1439_epoch_header_get (on page 98)
− returns the header value and the value of the
increment count for the epoch header.
age1439_epoch_header_enable (on page 98)
− controls whether or not epoch headers are
generated
age1439_epoch_header_enable_get (on page 98) −returns the current value of header
enable.
age1439_epoch_setup (on page 98)
−sets the parameters relevant to the transmission of
data epochs on the fiber interface.
age1439_epoch_size (on page 98) −sets the size of data epochs in bytes.
age1439_epoch_size_get (on page 98)
−returns the current size of data epochs.
age1439_error_message (on page 102)
−returns error information obtained from function
calls.
age1439_error_query (on page 103)
−queries the module for the most recent error.
age1439_ext_sample_sync (on page 104)
−enables and disables sync to an external sam-
ple clock
age1439_ext_sample_sync_get (on page 104)
−gets the state of external sample sync
age1439_fiber_BOF (on page 112)
−controls whether or not automatically generated
BOF events are transmitted
age1439_fiber_BOF_get (on page 112)
−returns the current value of bofEnable
age1439_fiber_clear (on page 106)
−clears all data from the fiber interface FIFO buffers
age1439_fiber_crc (on page 112) sets up the fiber interface to transmit and receive cyclic
redundancy checks.
age1439_fiber_crc_get (on page 112)
−returns the current status of the cyclic redundancy
check setting.
age1439_fiber_error_clear (on page 107)
−clears fiber errors from the status register
age1439_fiber_error_get (on page 108) −returns the value of the fiber interface error reg-
ister.
age1439_fiber_flow_control (on page 112)
−configures fiber flow control, enabling or
disabling transmitter flow control signals.
age1439_fiber_LED_get (on page 110)
−returns a data register indicating the state of the
front panel XMT/RCV led’s.
age1439_fiber_mode (on page 112)
−selects the fiber interface mode.
age1439_fiber_mode_get (on page 112)
−gets the current mode of the fiber interface.
age1439_fiber_rcv_signal_get (on page 111)
−displays the current value of PIO1, PIO2,
DIR and NRDY bits on the fiber receiver.
age1439_fiber_signal_get (on page 115) −returns a value indicating whether or not an
optical signal is detected by the optical fiber interface receiver.
age1439_fiber_setup (on page 112)
−sets the parameters associated with the fiber inter-
face.
age1439_fiber_transfer_rate (on page 112)
−selects the transfer rate for fiber optic data.
age1439_fiber_transfer_rate_get (on page 112)
−gets the current selection of transfer
rate for fiber optic data.
age1439_fiber_verify (on page 116) −preforms a verification of the fiber interface using
either an internal of external signal path.
age1439_fiber_xmt_BOF (on page 117)
−sends a BOF event used for synchronization