Flytec 6040 * - Manual (Page 9)

Operation Manual FLYTEC 6040 GPS
7
User defined data fields
There are 7 data fields in the lower part of the display which may be allocated individually.
In total more than 20 selectable data fields are at disposal. For list of data fields please refer
to 1.7 - User defined data fields page 10. (depending on firmware version!)
Alter data fields manually
Mark by repeated pressing of the ◄ arrow key the data field to be altered. The selected data field
shall be designated by a black bar. By use of the ▲ or ▼ arrow keys it is possible to assign
a new readout value to the selected data field. The field designation is displayed at the same time in big
lettering in Infoline 1.
If nothing is changed after having selected a field, the instrument returns to normal function after 10
sec. and the previous display is shown again
Alter data fields on the PC
All user defined readouts can be set comfortably by use of the freebie PC-Software Flychart on the PC
and be transferred via USB-interface onto the instrument
Caution: for safety reasons it is not possible to alter the user selectable fields during the flight
!
1.5.1.1 Shift page of data fields
The seven data fields exist 3 times on each page of data field! Therefore you have the possibility to
configure in total 21 data fields individually!
The very same function is also available on
the windlayer display page
!
Short pressing of the right side arrow key
gives access to the next page. The page
number is shown in the upper part of the
display next to the battery-charge state
readout as P1,
P2 or P3.
In -> Main Setup Menu -> Instr. settings ->
User fields
it is possible to configure these
readout pages with 4 big or 6 small fields !
We would like to present to the user some
proven recommendations in regard to the
default values of the 3 adjustable pages.
Some of the readouts are of such interest
that we recommend to keep them on each
of the 3 possible pages always at the same
position. For example: the “Speed over
ground - Gnd-Speed” or the wind
component “Speed diff.”
Example:
page 1) General Flight information is called up before the start or when the pilot is currently
in a normal balloon flight.
page 2) Navigation page is used if a Waypoint (WP) has been selected as goal to fly to.
Instead of the values recommended above, this field should mainly contain navigation readouts, such
as “Dist. to WP”, “Alt. a. BG”,; “Alt. a. WP”.
page 3) General information with altitude Alerter Here the pilot can configure the6 field-display. The
two new Data-fields can be used to display the upper and lower Altitude alert Level. The most important
data fields such as ONH and Envelop Temp, should also be present on this page.
Km/h
3
3
4
4
2
Diffgeschw
Int
-2.5
2816
14
m
57
90
80
60
P3
Dist Ziel
9.4
GLZ Gnd
11.2
40
N E
S W
70
50
30
Abw BGZiel
65
GLZ Ziel
10.5
Alti
Gps
Mod Alt 1 uv
m/s
Alt
1013
2
Km/h
3
3
4
4
2
Alt 2
Int
-2.5
2816
1165
m
57
90
80
60
P2
Kurs
42
Peilung WP
2:45
Dist WP
12 . 4
40
N E
S W
70
50
30
Abw SpurW
0.6
GLZ Soll
12
GLZ Grund
10.5
Alti
Gps
Mod Alt 1 uv
m/s
Alt
1013
2
Km/h
3
3
4
4
2
Alt 2
Int
-2.5
2816
1165
m
57
90
80
60
Time
16:08
FltTime
2:45
Temp
16
40
N E
S W
70
50
30
GLZGrund
8.6
Wind
12
GndGesch
56
Alti
Gps
Mod Alt 1 uv
m/s
Alt
1013
2
P1