KEPCO EL Series Electronic Load Operator Manual P/N 243-1295 Firmware Version 3.22 through 3.41 - Manual (Page 68)

B-8
SERIES EL 062011
B.47 [SOURce:]POWer:PROTection COMMAND
POW:PROT
Syntax: Short Form: [SOUR:]POW:PROT Long Form: [SOURce:]POWer:PROTection
where = power protection setpoint
Description: Selects power protection setpoint. This is a user-defined value which, if exceeded during operation,
causes a FAULT condition, forcing the load to disengage.
B.48 [SOURce:]POWer:PROTection? QUERY
POW:PROT?
Syntax: Short Form: [SOUR:]POW:PROT? Long Form: [SOURce:]POWer:PROTection?
Returns = power protection setpoint
Description: Indicates power protection setpoint.
B.49 [SOURce:]POWer:PROTection:STATe[:LEVel] COMMAND
POW:PROT:STAT
Syntax: Short Form: [SOUR:]POW:PROT:STAT[:LEV]
Long Form: [SOURce:]POWer:PROTection:STATe[:LEVel]
where: = 1 (enabled) or 0 (disabled)
Description: Clears or sets power protection trip.
B.50 [SOURce:]POWer:PROTection:STATe[:LEVel]? QUERY
POW:PROT:STAT?
Syntax: Short Form: [SOUR:]POW:PROT:STAT[:LEV]?
Long Form: [SOURce:]POWer:PROTection:STATe[:LEVel]?
where: = 1 (enabled) or 0 (disabled)
Description: Indicates whether the power protection level set using POW:PROT is enabled (1) or disabled
(0).
B.51 [SOURce:]RESistance[:LEVel][:IMMediate][:AMPlitude] COMMAND
RES
Syntax: Short Form: [SOUR:]RES[:LEV][:IMM][:AMP]
Long Form: [SOURce:]RESistance[:LEVel][:IMMediate][:AMPlitude]
Where: = resistance setpoint
Description: Establishes resistance setpoint. The resistance setpoint only affects the load when the load is in
Resistance mode of operation. Resistance setpoint is stored in non-volatile memory; value is restored
upon power-up.
B.52 [SOURce:]RESistance[:LEVel][:IMMediate][:AMPlitude]? QUERY
RES?
Syntax: Short Form: [SOUR:]RES[:LEV][:IMM][:AMP]?
Long Form: [SOURce:]RESistance[:LEVel][:IMMediate][:AMPlitude]?
Returns: = resistance setpoint
Description: Indicates resistance setpoint.
B.53 [SOURce:]VOLTage[:LEVel][:IMMediate][:AMPlitude] COMMAND
VOLT
Syntax: Short Form: [SOUR:]VOLT[:LEV][:IMM][:AMP]
Long Form: [SOURce:]VOLTage[:LEVel][:IMMediate][:AMPlitude]
where: = voltage setpoint
Description: Establishes voltage setpoint. The voltage setpoint only affects the load when the load is in Voltage
mode of operation. Voltage setpoint is stored in non-volatile memory; value is restored upon power-
up.
B.54 [SOURce:]VOLTage[:LEVel][:IMMediate][:AMPlitude]? QUERY
VOLT?
Syntax: Short Form: [SOUR:]VOLT[:LEV][:IMM][:AMP]?
Long Form: [SOURce:]VOLTage[:LEVel][:IMMediate][:AMPlitude]?
Returns: = voltage setpoint
Description: Indicates voltage setpoint.