Appendix b - scpi command/query definitions, B.1 introduction, Table b-1. scpi subsystem command/query index – KEPCO EL Series Electronic Load Operator Manual P/N 243-1295 Firmware Version 3.22 through 3.41 User Manual
Page 61
SERIES EL 062011
B-1
APPENDIX B - SCPI COMMAND/QUERY DEFINITIONS
B.1
INTRODUCTION
This appendix defines the SCPI subsystem commands and queries used with the Series EL
Electronic Load. Subsystem commands are defined in PAR. B.15 through B.102, arranged
Alphabetically in groups as they appear in the tree diagram, Figure 3-3. Table B-1 provides a
quick reference of all SCPI subsystem commands and queries used in the Interface Card.
NOTE: Message terminator requires CR and LF (see PAR. 3.13.5).
TABLE B-1. SCPI SUBSYSTEM COMMAND/QUERY INDEX
COMMAND
PAR.
COMMAND
PAR.
CAL:IPAD, ?
[SOUR:]VOLT:PROT:OVE, ?
CAL:IPMODE, ?
[SOUR:]VOLT:PROT:OVE:STAT[:LEV], ?
CAL:SUBN, ?
[SOUR:]VOLT:PROT:UND, ?
CAL:GATE, ?
[SOUR:]VOLT:PROT:UND:STAT[:LEV], ?
CAL:GPIB, ?
STAT:CHAN[:EVENT]?
CAL:DNS, ?
STAT:CHAN:COND, ?
DEB:ECHO, ?
STAT:CHAN:ENAB, ?
DEB:TREE:DISP
STAT:CSUM[:EVENT]?
DEB:TREE:SEP, ?
STAT:CSUM:ENAB, ?
LOCK, ?
STAT:OPER[:EVENT]?
[SOUR:]INP[:STAT], ?
STAT:OPER:COND?
[SOUR:]INP:PROT:CLE
STAT:OPER:ENAB, ?
[SOUR:]INP:SHOR[:STAT]
STAT:OPER:NTR
[SOUR:OUTP[:STAT], ?
STAT:OPER:PTR
[SOUR:]OUTP:PROT:CLE
STAT:QUES[:EVENT]?
[SOUR:]OUTP:SHOR[:STAT]
STAT:QUES:COND?
[SOUR:]MEAS:ALL
STAT:QUES:ENAB, ?
[SOUR:]MEAS:ALL2
SYST:DAMP, ?
[SOUR:]MEAS[:SCAL]:CURR[:DC]
SYST:ERR?
[SOUR:]MEAS[:SCAL]:POW[:DC]
SYST:EXT, ?
[SOUR:]MEAS[:SCAL]:VOLT[:DC]
SYST:FAN, ?
[SOUR:]COND[:LEV][:IMM][:AMP], ?
SYST:PFM, ?
[SOUR:]CURR[:LEV][:IMM][:AMP], ?
SYST:PFM:LIST?
[SOUR:]CURR:PROT, ?
SYST:PFM:STAT?
[SOUR:]CURR:PROT:STAT[:LEV], ?
SYST:RANG:CURR, ?
[SOUR:]MODE, ?
SYST:RANG:POW, ?
[SOUR:]POW[:LEV][:IMM][:AMP], ?
SYST:RANG:VOLT, ?
[SOUR:]POW:PROT, ?
SYST:REPLY, ?
[SOUR:]POW:PROT:STAT[:LEV], ?
SYST:SERN?
[SOUR:]RES[:LEV][:IMM][:AMP], B.51,
SYST:SETT?
[SOUR:]VOLT[:LEV][:IMM][:AMP], ?
SYST:VERS?