KEPCO EL Series Electronic Load Operator Manual P/N 243-1295 Firmware Version 3.22 through 3.41 - Manual (Page 4)

ii
SERIES EL 062011
TABLE OF CONTENTS
SECTION PAGE
3.8 Changing IP Mode ..................................................................................................................................... 3-4
3.9 Changing Static IP Address or Subnet Mask............................................................................................. 3-4
3.10 Changing GPIB Address............................................................................................................................ 3-5
3.11 Operation of Master/slave Configurations.................................................................................................. 3-5
3.11.1 Power Up ................................................................................................................................................ 3-6
3.11.2 Local (Front Panel) Operation ................................................................................................................ 3-6
3.11.3 Remote (Computer) Operation ............................................................................................................... 3-6
3.11.4 Indications During Master/Slave Operation ............................................................................................ 3-6
3.11.5 Master/Slave Controls and Indicators..................................................................................................... 3-6
3.11.6 Master/Slave Operating Notes/Cautions/Warnings ................................................................................ 3-7
3.11.7 Master/Slave Disconnect ........................................................................................................................ 3-7
3.12 Operation via Computer Interface.............................................................................................................. 3-7
3.13 SCPI Programming .................................................................................................................................... 3-8
3.13.1 SCPI Messages ...................................................................................................................................... 3-8
3.13.2 Common Commands/Queries ................................................................................................................ 3-8
3.13.3 SCPI Subsystem Command/Query Structure......................................................................................... 3-11
3.13.3.1 Calibration Subsystem....................................................................................................................... 3-11
3.13.3.2 Debug Subsystem ............................................................................................................................. 3-11
3.13.3.3 PROTection Subsystem .................................................................................................................... 3-12
3.13.3.4 [SOURce:]MEASure Subsystem ....................................................................................................... 3-12
3.13.3.5 [SOURce:]InPut, [SOURce:]OUTPut Subsystems ............................................................................ 3-12
3.13.3.6 [SOURce:]VOLTage, [SOURce:]CURRent, [SOURce:]POWer Subsystems.................................... 3-12
3.13.3.7 [SOURce:]Resistance, [SOURce:]CONDuctance Subsystems......................................................... 3-12
3.13.3.8 STATus Subsystem........................................................................................................................... 3-12
3.13.3.9 SYSTem subsystem .......................................................................................................................... 3-12
3.13.4 Program Message Structure................................................................................................................... 3-13
3.13.4.1 Keyword............................................................................................................................................. 3-13
3.13.4.2 Keywords for Dual Units .................................................................................................................... 3-13
3.13.4.3 Keyword Separator............................................................................................................................ 3-13
3.13.4.4 Query Indicator .................................................................................................................................. 3-13
3.13.4.5 Data ................................................................................................................................................... 3-13
3.13.4.6 Data Separator .................................................................................................................................. 3-13
3.13.4.7 Message Terminator.......................................................................................................................... 3-14
3.13.5 Understanding The Command Structure ................................................................................................ 3-15
3.13.6 Program Message Syntax Summary ...................................................................................................... 3-15
3.13.7 Status Reporting ..................................................................................................................................... 3-16
3.13.7.1 Status Reporting Structure ................................................................................................................ 3-16
3.13.7.2 Standard Event Status Register ........................................................................................................ 3-16
3.13.7.3 QUEStionable Status Register .......................................................................................................... 3-18
3.13.7.4 Channel Status Register.................................................................................................................... 3-18
3.13.7.5 Channel Summary Register .............................................................................................................. 3-19
3.13.7.6 Status Byte Register.......................................................................................................................... 3-19
3.14 Damping..................................................................................................................................................... 3-19
3.14.1 Damping Adjustments............................................................................................................................. 3-19
3.15 Analog Programming ................................................................................................................................. 3-21
3.16 Operator Maintenance ............................................................................................................................... 3-22
APPENDIX A - IEEE 488.2 COMMAND/QUERY DEFINITIONS
A.1 Introduction ................................................................................................................................................ A-1
A.2 *CLS — Clear Status Command................................................................................................................ A-1
A.3 *ESE — Standard Event Status Enable Command ................................................................................... A-1
A.4 *ESE? — Standard Event Status Enable Query........................................................................................ A-2
A.5 *ESR? — Event Status Register Query ..................................................................................................... A-2
A.6 *IDN? — Identification Query..................................................................................................................... A-2
A.7 *OPC — Operation Complete Command .................................................................................................. A-2