Watlow Series 988LF - Manual (Page 59)

Appendix WATLOW Series 988LF Users Manual A.5
Q, R
range high 1 4.4 - 4.5
range high 2 4.7 - 4.8
range low 1 4.4 - 4.5
range low 2 4.7 - 4.8
rate
output 1 5.3
output 2 5.4
rate band A.3
reference junction A.2
relay, mechanical 7.1
release tabs 1.1, 2.2
remote set point 4.6
removing controller chassis 1.1, 2.2
reset
output 1 5.3
output 2 5.4
restore 6.5
retransmit A.3
RTD A.3
RTD calibration curve 4.5
RTD input 2.3
RTD wiring
input 1 2.7
remote set point option 2.8
S
safety practices 2.3, 2.5, 2.6
sensor installation 2.3
sensor type
input 1 4.3
serial number 6.2
set point 2 5.2
setting DIP switches 1.1 - 1.3
input 1.2
lockout 1.3
Setup Menus 4.1 - 4.10
shipping claims A.1
silencing 4.10
silencing alarms 7.3
slidewire feedback A.3
software revision 6.2
specifications A.6
square root extraction (linearization, square
root) A.2
switched dc, open collector wiring
output 1 2.9
output 2 2.10
switching sensitivity A.3
T
technical assistance iii, 6.3
temperature limit control protection 2.5
terminal designation stickers 2.3
test displays 6.3
test output 6.4
thermal system A.3
thermocouple 2.3, A.3
thermocouple break protection A.3
thermocouple wiring
input 1 2.7
remote set point option 2.8
three-mode control A.3
time proportioning control A.3
tuning
automatic 7.1 - 7.2
manual 7.2
Tuning of Industrial Control Systems 7.1
U
Up-arrow Key 3.1
upper display 3.1
using manual ii - iii
Index / Prompts
V, W
warnings iii
warranty A.1
wiring 2.1, 2.3 - 2.10
input 1 2.7
input 2 2.8
output 1 2.9
output 2 2.10
wiring example 2.5
wiring safety 2.3, 2.5, 2.6
X, Y, Z
zero switching A.3
Prompt Index
[----] (error) 7.5
A
[Acnt] (Ambient A/D count) 6.2
[`AHI] (alarm high) 5.6
[`ALO] (alarm low) 5.6
[`ALt] (alarm type) 4.10
[AMb] (ambient temperature) 6.2
[`AUt] (auto-tune) 5.7
B
[bPLS] (bumpless transfer) 7.3, 7.5
C
[`C_F] (Celsius_Fahrenheit) 4.8
[`CAL] (calibration offset) 5.7
[`CAL] (Calibration Menu) 6.5
[`Ct1] (cycle time, output 1) 5.3
[`Ct2] (cycle time, output 2) 5.5
D
[DAtE] (factory ship date) 6.2
[``db] (dead band) 5.5
[`dEC] (decimal) 4.6
[dFLt] (default) 4.3
[diAg] (Diagnostics Menu) 6.1
[dISP] (test displays) 6.3
E
[E1`1] (A/D underflow error) 7.5
[E2`1] (A/D underflow error) 7.5
[E1`2] (sensor under-range error) 7.5
[E2`2] (sensor under-range error) 7.5
[E1`3] (sensor over-range error) 7.5
[E2`3] (sensor over-range error) 7.5
[E1`4] (A/D overflow error) 7.5
[E2`4] (A/D overflow error) 7.5
[`Er3] (ambient temperature error) 7.6
[`Er4] (RAM identification error) 7.6
[`Er5] (non-volatile checksum error) 7.6
[`Er9] (configuration error) 7.6
F
[Fcty] (Factory Menues) 6.1
G, H , I
[`In1] (input 1) 4.3
[itY1] (input 1 module type) 6.3
[itY2] (input 2 module type) 6.3
J, K, L
[`LAt] (latching) 4.10
[`LOC] front panel lockout) 4.2
[`L-r] (local-remote) 5.7
M, N, O
[OPLP] (open loop) 6.4, 7.6
[`Ot1] (output 1) 4.9
[`Ot2] (output 2) 4.9
[OtY1] (output 1 module type) 6.3
[OtY2] (output 2 module type) 6.3
P
[`Pb1] (proportional band, output 1) 5.2
[`Pb2] (proportional band, output 2) 5.4
Q, R
[`rA1] (rate, output 1) 5.3
[`rA2] (rate, output 2) 5.4
[`rE1] (reset, output 1, Pid A) 5.3
[`rE2] (reset, output 2, PID A) 5.4
[`rH1] (range high 1) 4.4 - 4.5
[`rH2] (range high 2) 4.7 - 4.8
[`rL1] (range low 1) 4.4 - 4.5
[`rL2] (range low 2) 4.7 - 4.8
[`rSP] (remote set point) 4.6 - 4.7
[`rSt] (restore) 6.5
[`rtd] (RTD calibration curve) 4.5
S
[`SIL] (silencing) 4.10
[``Sn] (serial number) 6.2
[SOFt] (software revision) 6.2
[`SP2] (set point 2) 5.2
T , U, V, W, X, Y, Z
[tout] (test outputs) 6.4