Wh200 headset operation, Ation, Wh200 headset oper – Clear-Com HME DX100 User Manual
Page 27
23
ATION
he Headset control buttons will activate when pressed lightly.
Press and release the power button on the inside
say
•
ume-down T
•
ode — To set the Headset for HF communication, with the power off, press and hold
an
•
ocked out, with the power off, press and
off, press an
old the ISO
•
and transmit lights from coming on during headset operation,
NOTE:
n
f and
le.
.
•
ease
own for more
NOTE: In HF mode, pressing the IC1 or IC2 button while latched in ISO will latch on IC. Pressing the ISO
button while latched in IC will latch on ISO.
WH200 HEADSET OPER
T
Use your fingertips, not your fingernails, to press the buttons.
Power On/Off
• Power On —
of the Headset housing. A voice message in the earpiece will
“Power on, Headset #, Version #” and the power light will go on.
The REGISTRATION STATUS indicator on the base station will
momentarily indicate the Headset ID number.
Power Off — Press and hold the power button for approximately
3 seconds. A voice message in the earpiece will say “Power off,”
and the power light will go off.
ISO (Isolate) and IC (Intercom)
Use the ISO button to communicate with other Headset/Beltpac/Speaker Station
causing the ISO button to function the
users. The ISO feature can be locked out,
same as the IC button.
Use the IC1
or IC2 button to communicate via the intercom channel.
• Push-To-Talk (PTT) Mode — To set the Headset for PTT
communication, with the power off, press and hold the vol
and
ISO buttons while you press and release the power button. You will hear
“Power on, Headset #, Version #, Hands-free off” in the earpiece. Press and hold the IC1,
IC2 or ISO button
while talking.
Hands-Free (HF) M
Power
button
Power
light
Transmit
light
the volume-up S and ISO buttons while you press and release the
power button. You will hear “Power on,
Headset #, Version #, Hands-free on” in the earpiece. When set up for HF communication, the Headset c
be operated in either HF or PTT.
ISO Lockout Mode — To set the Headset with the ISO feature l
hold the IC1 button while you press and release the power button. You will hear “Power on, Headset #, Version
#, ISO off” in your Headset earpiece. When set up for the ISO Lockout mode, the ISO button will operate
the same as the IC1 button, in either hands-free or PTT communication.
To reset the ISO feature for normal ISO button communication, with the power
d h
and IC1 buttons while you press and release the power button. You will hear “Power on, Headset #, Version #,
ISO on” in your Headset earpiece.
Lights-off Mode — To prevent the power
press and hold the IC2 button while you press the power button to turn the headset on.
To return the lights to their normal functions, turn the power off and on again without pressing the IC2 button.
The above settings are saved in memory and only need to be repeated when you want to change betwee
HF and PTT operation. When changing modes, if both power lights begin blinking, turn the Headset of
begin again. HF and PTT mode settings affect both IC and ISO. Individual adjustment is not possib
• Push-To-Talk (PTT) Mode Operation — Press and hold the IC1, IC2 or ISO button while speaking
In PTT operation, audio will be transmitted only while you are pressing the IC1,
IC2 or ISO button.
Hands-Free Mode (HF) Operation — Quickly press and release the IC or ISO button to “latch” the
transmitter on in the HF mode. Talk and listen, as in a normal telephone conversation. Press and rel
the IC or ISO button again to “unlatch,” to end the conversation. If either button is held d
than a half second, the Headset will function as PTT. All Headsets/Beltpacs/Speaker Stations can be
unlatched by the base station operator, by pressing the UNLATCH button on the base station.