Beltpac operation – Clear-Com HME DX100 User Manual

Page 25

Power

lights

BELTPAC OPERATION

The Belt
pressed firmly. Use your fingertips, not your fingernails, t

Pow

• Pow

button

A v

Beltpac

and

d ISO

Afte

indi

he REGISTRATI

dicator on the base station will momentarily indicate the ID

ltpac.

•

ower Off — Press and hold the PWR button for approximately 2 seconds.

voice message in the earpiece will say “Power off,” and the green power light will go off.

NOTE: While the Beltpac is transmitting, the green power light will be flashing.

The green power light will be on steady whenever the Beltpac is ready, but not transmitting.

ISO

Use the ISO button to communicate with other Beltpac/Headset/Speaker Station users. The ISO feature can be
lock

e as the IC button.

Use the I

nnel.

• Pus

et the Beltpac for PTT communication, with the power off, press and

hold

d ISO buttons while you p

e PWR (power) button. You will hear

Power on, Beltpac #, Version #, Hands-free off” in the

e. Press and hold the IC or ISO

utton while talking.

•

ands-Free (HF) Mode — To set the Beltpac for HF communication, with the power off, press and hold

e volume-up S and ISO buttons while you press and release the PWR (power) button. You will hear

Power on, Beltpac #, Version #, Hands-free on” in your headset earpiece. When set up for HF
ommunication, the Beltpac can be operated in either HF or PTT.

•

O Lockout Mode — To set the Beltpac with the ISO feature locked out, with the power off, press and

PWR (power) button. You will hear “Power on, Beltpac #,

Ver

n set up

SO Lockout mode, the ISO button will

oper

hands-free or PT

unication.

To r

municat

th the power off, press and ho

and

u will hear “Power on, Beltp

Ver

NOTE:

ry and only nee

epeated when you want to change between

HF and PTT operation. When changing modes, if both power lights begin blinking, turn the Beltpac off and
begin again. HF and PTT mode settings affect both IC and ISO. Individual adjustment is not possible.

•

ush-To-Talk (PTT) Mode Operation — Press and hold the IC or ISO button for more than one

cond. In PTT operation, audio will be transmitted only while you are pressing the IC or ISO button.

•

to “latch” the

ss and release

the

ation. If either button is held down for more

than a half second, the Beltpac will function as PTT. All Beltpacs/Headsets/Speaker Stations can be
unlatched by the base station operator, by pressing the UNLATCH button on the base station.

NOTE: In HF mode, pressing the IC button while latched in ISO will latch on IC. Pressing the ISO button

while latched in IC will latch on ISO.

pac control buttons have a snap action. They will activate when

o press the buttons.

er On/Off

er On — Press and release the PWR (power)

oice message in the earpiece will say “Power on,

the red power lights at the corners of the IC an

r a short time, one light will go off and the other wi

cating the Beltpac is ready for use. T

#, Version #,”

buttons will go on.

ll change to green

ON STAT

of the Be

in
P
A

(Isolate) and IC (Intercom)

ed ut, causing the ISO button to function the sam

C button to communicate via the intercom cha

h-To-Talk (PTT) Mode — To s

the volume-down T an

ress and release th

headset earpiec

“
b
H
th
“
c
IS
ho the IC button while you press and release the

sion #, ISO off” in your headset earpiece. Whe

ate the same as the IC button, in either

eset the ISO feature for normal ISO button com
IC buttons while you press and release the PWR

sion #, ISO on” in your headset earpiece.

The above settings are saved in memo

for the I

T comm

ion, wi

ld the ISO

ac #,

ower) button. Yo

d to be r

P
se
Hands-Free (HF) Mode Operation — Quickly press and release the IC or ISO button
tra smitter on in the HF mode. Talk and listen, as in a normal telephone conversation. Pre

IC or ISO button again to “unlatch,” to end the convers